The Quality Of Shoe Material Includes Two Parts, Vamp And Shoe.

< p > natural leather is less than a href= "http://www.91se91.com/" > real leather < /a >. It has pores. When the eyes are difficult to see clearly, thumb can be pressed on the leather surface to see if there is a fine leather pattern beside the thumb.

It has fine texture, disappearance of fine lines after releasing hands, good elasticity of leather shoes, and better natural leather.

If there is no fine grain, most of them are not natural leather, including two layers of shaving film leather.

< /p >

Another notable feature of < p > natural leather is that there are blemishes on the surface.

Generally, the natural leather upper is slightly defective in the inside of the shoe and in other inconspicuous places, such as uneven skin width, bright furuncle, tick boil and so on.

There are three layers of cross section of natural leather, which are dense and different. The epidermis is very fine and flexible, and there are dense dermis in the middle. The following is a loose meat surface fiber layer, and there is no obvious demarcation between layers.

< /p >

< p > leather shoes < a href= "http://www.91se91.com/" > shoe lining < /a > is a reinforcing material used to prevent stretching deformation and improve foot touch.

It is required that the shoe lining material has fine touch, breathability, excellent moisture absorption and moisture retention, and no color loss.

The middle and upper leather shoes are made of natural leather and cotton cloth.

If the vamp is natural leather, the shoe lining is the artificial substitute leather. It can only be regarded as the middle and low grade shoes.

Most consumers ignore the choice and identification of shoe lining materials, which is wrong.

< /p >

< p > 2., look at the upper a href= "http://www.91se91.com/" > suture line < /a > and the bottom seam, identify the quality of processing < /p >

< p > see if there is a broken line and whether the upper stitch is neat and regular.

In particular, the bonding part of the adhesive shoe leather bottom should be glued and smoothed without any gap, and there is no indication of virtual sewing and glue opening.

< /p >

< p > 3.. Touch the inner cavity of the shoe with your hands and see if there is a bumpy phenomenon inside and inside the shoe < /p >

< p > where the feet can be touched, they should not be uneven or their feet will blister.

The shoe must be provided with an insole, which is designed to keep the shoes clean, covering the rugged nails at the bottom and improving the touch of the feet.

< /p >

< p > 4.. Use hand to pinch the heel of the upper to see if it is stiff and elastic. < /p >

< p > requires that there should be no groove mark on the stiff part, and good elasticity below the ankle.

< /p >

< p > 5. press the bottom of the waist to see if it is hard < /p >.

< p > the bottom of the shoe is the trunk and skeleton of the shoe, and press hard as the bottom of the shoe.

If the skeleton and trunk are not stiff, the shoes must be deformed and damaged.

< /p >

< p > 6.. Place your shoes on the table or glass panel at random, to see if the shoes are stable. < /p >

< p > when the shoes are placed on the table, they should stop immediately.

< /p >

< p > {page_break} < /p >

< p > 7.. Insert the middle finger tip under the front toe sole to see if the height of the fore step is suitable (< /p >).

< p > when the tip of the shoe tip is just enough for the middle finger to indicate the belly thickness, it indicates that the front toe of the shoe tip is suitable.

When the front toe of the shoe tip is too large, the stability is reduced; the shoe toe is worn quickly before the foot is lifted, the shoe is easily deformed, and the foot is easy to fatigue.

< /p >

< p > 8. holding your shoes with your hands, see < a href= "http://www.91se91.com/ > > sole > /a > a href=" http://www.91se91.com/ "> shoe heel > /a > contact is stable. < /p >

< p > light the sole and heel lightly on the side of the table (or counter), so that the side of the shoe is upwards to view the contact area of the sole.

It is better to contact the side of the table with the sole (the widest part of the sole) and the whole heel plane.

Otherwise, shoes will be easy to deform and drop heels.

< /p >

< p > 9. will be "a href=" http://www.91se91.com/ "> shoes < /a > flat on the table, from the front and rear two directions to see whether it is correct" /p ".

< p > first, from the toe of the shoe, look at the size of the inside and outside edges of the sole from the top of the table.

From the heel of the shoe, check whether the heel is vertical or not, so that it does not tilt to the inside or outside.

< /p >

< p > 10. with index finger erected on the outside side of the shallow shoes, look at the upper ankle height, < /p >.

< p > the index finger of the forefinger contacts the inner sole of the shoe downwards and lets the index finger close to the upper part of the outer ankle to see the second finger knuckle line of the index finger and whether it is highly consistent with the upper arm of the outer ankle.

General life shoes, social etiquette shoes, fashion shoes, slightly lower than the index finger second finger knuckle line is good; low waist sports shoes and casual shoes are soft mouth structure, the external ankle height can slightly higher than the index finger second finger joint line.

< /p >

< p > 11. overlooking the vamp from up to down to see the symmetry of the shoe parts and the distortion of the shoe outline (/p >).

< p > take the straight line between the tip of the shoe and the middle point of the heel as the symmetrical axis to see whether the components on the vamp are symmetrical or not.

The shoe outline should be folded in the shoe, smooth and round, and the twisted leaf should be twisted into inferior shoes.

< /p >

< p > 12.. Understand the shoe's outsole performance and choose the suitable outsole < /p >.

There are many outsides of < p > < a href= > http://www.91se91.com/ > shoes > /a >. According to the main raw materials, it can be divided into rubber bottom, imitation leather base, plastic bottom and so on. Their properties are: Rubber soles are soft, elastic, skid resistant, wear resistant, heat-resistant and cold resistant.

It's just a little heavier.

< /p >

< p > imitation leather sole, light, stiff, wearable and resistant to twists and turns.

But the elasticity is poor and not too slippery.

Plastic sole has good abrasion resistance and elasticity.

But the texture is hard, and the heat resistance and cold resistance are poor.

< /p >