• <abbr id="ck0wi"><source id="ck0wi"></source></abbr>
    <li id="ck0wi"></li>
  • <li id="ck0wi"><dl id="ck0wi"></dl></li><button id="ck0wi"><input id="ck0wi"></input></button>
  • <abbr id="ck0wi"></abbr>
  • <li id="ck0wi"><dl id="ck0wi"></dl></li>
  • Home >

    Five Key Factors To Help You Improve The Quality Of Compact Spinning

    2020/1/6 9:37:00 0

    Compact Spinning Quality

    Negative pressure fan discharge volume and negative pressure tube negative pressure

    The negative pressure of the negative pressure tube is the most direct and crucial factor affecting the quality of compact yarn. The accumulation of flowers in the bellows of negative pressure fans is also a key factor affecting the negative pressure of negative pressure pipes. In daily production, it is necessary to clean up the bellows and maintain negative pressure stability in time.

    According to actual testing and production, compact spinning negative pressure should be kept at 24-30 mbar. Low negative pressure will lead to higher breakage rate, increased hairiness, longer hairiness and larger unevenness of hairiness. According to the measured results, under the same temperature and humidity condition, the negative pressure difference between the front end and the rear end of the vehicle is about 1.5-3.5 mbar when the negative pressure is 24-27 mbar, and the hairiness difference is about 30%. Production practice has proved that 4.2 kW negative pressure fans can be selected for 1008 spindles, and 2.4 kW negative pressure fans can be selected for 512 spindles. Properly increasing the speed of the negative pressure fan can reduce the negative pressure difference between the head and the tail and minimize the effect of the negative pressure difference on the yarn quality. Each time the vehicle is wiped, the negative pressure fan is opened, and the accumulated flowers accumulated in the negative pressure air duct are sucked out and cleaned.

    Motion state of whisker on negative pressure pipe

    The movement of the whisker on the negative pressure tube is a very important factor that affects the yarn evenness. When the negative pressure is normal, the bar must move in a straight and continuous state when the rollers transfer to the negative pressure tube and move on the negative pressure pipe. However, the motion state of the bar must be affected by some factors.

    In actual production, due to the excessive pressure of the cradle, the accumulation of static electricity, the poor surface of the roller, and the small negative pressure of the negative pressure pipe, the phenomenon of falling or skewing in the "no control zone" between the roller and the negative pressure tube will result in the obvious influence on the yarn line. Therefore, the pressure of compact spinning cradle should be small, so as to prevent static electricity accumulation, keep the surface smoothness of roller and roller, prevent entangling and maintain negative pressure of negative pressure tube. At the same time, try to choose antistatic grid ring and choose mesh ring with reasonable mesh number.

    Effect of temperature and humidity on workshop

    In the process of compact spinning, due to suction and draining, the temperature of the workshop will be obviously uneven at the front and rear of the vehicle. This uneven will show seasonal differences, the temperature difference in winter is about 2-4 degrees, while the summer is about 3-6 degrees Celsius. Temperature and humidity are important factors affecting hairiness. According to actual measurement, the hairiness and NEP number of the tail are about 40% higher than that of the headstock, see Table 1. Therefore, maintaining the normal temperature and humidity of workshop and reducing the difference between temperature and humidity are important measures to improve product quality.

    Cradle pressure

    Cradle pressure has a direct impact on yarn quality. Too much pressure on the cradle can easily shorten the service life of the front cots, causing the concave of the front cots and the mechanical waves of cots. The normal use period of the front cots is about 2 months. When the pressure is too high, the phenomenon of poor grip on roving will occur for a month and a half, resulting in a rapid increase in breakage. So compact spinning should not be too high pressure, generally controlled in 160-180N/ double spindle is appropriate.

    Effect of spinning process on yarn quality

    Floating zone is a key factor affecting yarn quality. The size of the floating area should be the same size, the pressure bar position is moderate, and the pressure roller can not appear before the grinding roller and the long leather rim. When the pressure bar is located, the floating area will be too large to control the fiber and even wear the leather apron. When the pressure bar is too high, it will cause roving to run up, and it can not play the role of the pressure bar. If the roller is pulled before the pressure bar, it will also cause the mechanical wave of the roller. In production, it is advisable to punch 2-3mm before the cots, and the maximum should not exceed 3mm. If the former impulse is too large, it will be easy to form an anti encircling arc, resulting in a decrease in yarn quality and an increase in breakage. It is easy for the compact spinning floating area to cause the front cot roller to press the grid ring. When the bar movement moves to the two sides of the guide yarn, the bar must swing around the suction trough to affect the yarn quality.

    Reasonable draft distribution is also an important factor to improve yarn quality. When selecting drafting multiple, we can not simply pursue good yarn evenness and neps. With increasing drafting times, the long segment irregularity will also increase. In the selection of compact spinning process, the drafting ratio of the back zone can be increased appropriately and the spindle speed can be increased beyond the critical drawing ratio, thus increasing the yarn yield and improving the efficiency.

    The optimization of yarn quality is a complex project. The factors affecting yarn quality are complex and diverse. Therefore, the yarn quality should be optimized in order to get the best yarn quality.

    • Related reading

    5 Enterprises Such As China Textile, Limited By Share Ltd And So On Have Been Awarded 20Th Anniversary National Product Development Bases For Collaborative Development.

    Fabric accessories
    |
    2020/1/3 18:59:00
    39

    Tian Wang Textile 100 Thousand Spindles Cotton Spinning Production Line Put Into Operation

    Fabric accessories
    |
    2020/1/3 18:59:00
    144

    2019 China'S Textile And Garment Industry'S Three Annual Example

    Fabric accessories
    |
    2020/1/3 18:59:00
    72

    Electricity Supplier Observation: In 2020, Live TV Providers Will Welcome Another Outbreak.

    Fabric accessories
    |
    2020/1/3 18:59:00
    20

    Jiang Mingcheng And His Party Went To Ganzhou To Investigate The Development Of Textile And Garment Industry

    Fabric accessories
    |
    2020/1/3 18:59:00
    187
    Read the next article

    ICE Cotton Futures Fell From Seven Month High, Killing Iran Commander Due To Us Air Raid.

    According to foreign news on January 3rd, ICE cotton futures fell on Friday from the seven month high on the previous day, due to the deterioration of risk sentiment.

    主站蜘蛛池模板: 日韩中文字幕网| 久久久精品中文字幕麻豆发布 | 3d区在线观看| 激情综合色五月六月婷婷| 天堂在线最新资源| 免费**毛片在线搐放正片| chinese乱子伦xxxx视频播放| 男生和女生一起差差差差| 日韩三级在线免费观看| 国产后入又长又硬| 久久久久久亚洲av无码专区| 足本玉蒲团在线观看| 攵女yin乱合集高h文| 啊灬啊灬啊灬岳| 一本到视频在线| 狠狠精品干练久久久无码中文字幕 | 欧美xxxx新一区二区三区| 国产欧美久久一区二区| 久久精品免视看国产成人 | 色屁屁www欧美激情在线观看| 无码无套少妇毛多69XXX| 嘟嘟嘟www在线观看免费高清| 一本一道波多野结衣大战黑人| 男女国产一级毛片| 在线永久免费观看黄网站| 亚洲性生活网站| 黑色丝袜美腿美女被躁翻了| 欧美伊久线香蕉线新在线| 国产成人综合亚洲AV第一页| 久久人人爽人人爽人人av东京热| 翁熄系列乱老扒bd在线播放| 女扒开尿口让男桶30分钟| 亚洲精品二三区伊人久久| 亚洲偷自精品三十六区| 日本卡三卡四卡免费| 北条麻妃在线视频观看| 99re在线播放视频| 狠狠色欧美亚洲狠狠色www| 国产精品日本一区二区不卡视频| 人人妻人人澡人人爽欧美精品| 2021国产麻豆剧果冻传媒影视|