Code Of Practice For "Tailor" In Garment Factories

There are two main tasks.

1 scissors and 2 rows of materials (including sample and bulk goods).

The responsibilities of these two tasks are quite significant, and the quality of the company's sample (shape and size) will be directly related to the cost of the material.

Therefore, the staff who are required to do the job must strictly follow the code of conduct and strict requirements for each piece, and calculate the amount of each part.

Where there is something to be understood, it can be tailored.

Reduction

The quality of the products directly affects the quality of the samples. Therefore, no matter whether the sample is cut or not, it must be cut according to the size of the pattern, and it is not allowed to change the pattern and cutting of the pattern at will, and we should pay attention to the following code of conduct.

1: the head office, A: arrange the materials and get the order. First, check the cloth numbers according to the cloth number on the order sheet, and then discharge the accurate sample materials and materials.

If the fabric needs to be blandied, the length of the fabric should be appropriately increased on the basis of discharging.

On the contrary, if there is no need for blanching fabrics, they should be ordered according to the actual materials.

And the amount of materials used for each fabric, lining and other accessories should be recorded on the books and paper bags for archiving and sealing.

B: shrinkage rate, all head office must first blanching and cutting, to ensure the size of the sample. C: tailoring, first of all depends on the office or style map to check the number of cutting pieces of the pattern, separate the different fabric cut fabrics, especially pay attention to the fabric lines, if the fabric is straight fabric must be changed to cross cutting (Wei Xiangcai).

All stripes, lattices, and printed fabrics must be cut according to the requirements of the production list.

The position of the knife eye must be cut according to the pattern position.

If the pattern or pattern of the pattern is found to be wrong in the trimming, the paper master should be notified first.

The 2 is to cut two offices. The operation procedure of the two units is almost the same as that of the head office. However, when revising two, we should pay attention to the revision of the paper bag and see whether there is any special requirement for the revised instructions.

3: as a result of the re run office, since the re run is a sample of large goods, it is necessary to use the large cargo fabric to do the job to ensure that the size of the large sample can be the same as the size of the big goods (closer), and the shrinkage rate of the fabric must be tested first, and the shrinkage rate of the fabric can be determined before the tailoring can be made. (the shrinkage rate of the material within 4% is not blanking, the fabric shrinkage rate must exceed 4% must be blanching).

Because they are all M yards, and large goods usually have more than 3 yards, so when calculating the material for large goods, we should see the size produced by large goods, and then according to the average middle size of large goods, we need to arrange large quantities of materials.

If there is a single set, it is necessary to set up a large list of materials.

Discharge materials: because some of the items are not re run, they are directly used to make materials for bulk goods. Therefore, when the average amount of materials is used, the size of the yard should be increased by one yard, and the shrinkage rate can be used as the average material. The bulk material is based on the material used for discharging the average middle code pattern of all the codes of large goods, plus the shrinkage rate of the fabric, which can be used as material for large goods.

Pattern: all samples should be compared with the quantity of the pattern. If the pattern is found to be uneven, the paper master should be informed immediately. If the cutting piece is found to be insufficient and less cut when the car is run, it will be fined three yuan for each pattern.

Responsibility: the operator must be fully responsible for the amount of calculation and the sample he ordered. The difference between the material and material used for the actual delivery of the goods is not more than 5%.

It is due to negligence or negligence that the sample is redone and the goods are not accurately used, depending on the severity of the consequences, warnings, fines or dismissal should be given.