• <abbr id="ck0wi"><source id="ck0wi"></source></abbr>
    <li id="ck0wi"></li>
  • <li id="ck0wi"><dl id="ck0wi"></dl></li><button id="ck0wi"><input id="ck0wi"></input></button>
  • <abbr id="ck0wi"></abbr>
  • <li id="ck0wi"><dl id="ck0wi"></dl></li>
  • Home >

    Pick Up Method Of Zipper Women'S Boot Template After Full Service

    2008/8/11 10:07:00 41781

    Women's boots with zipper structure are popular with women of all ages because of their fashionable style, soft material, comfortable clothing and different bottom.

    However, because the shoe type of this type of structure is special, the difficulty of taking off is too great, which also brings many troubles to the production designer.

    In this paper, a method of taking stilts is introduced. By controlling some data to get stilts, the made sample plate is not difficult to take the last under the condition of hand last. This method has strong maneuverability and can analyze the advantages of the problem quickly and conveniently.


     

    Next, take a short boot (from the boot to the last one) to illustrate the method of taking off.

    Production steps

    1. Paste half last, draw the middle line.

    Two. Exhibition flat (see Figure 2)


    During the exhibition, the wrinkles are evenly dispersed to the bottom, and there is no pleat at the back midline.

    Then add a certain amount of material thickness (shoe thickness, main heel and other material thickness) at the rear arc.

    Three. Take off

    In the process of taking off, it is necessary to ensure that the center line and the length of the model are equal to that of the last face, and the bottom edge is allowed to be shortened appropriately.

    The 1. part of the painting is the latter part: the concave part of the middle line of the template (the most concave part of itself) can be aligned with the broken line of the template, so that both ends of the back line can exceed the broken line, and the ends of the ends should not exceed too much (less than 15MM).

    Then draw the back part of the template on the template, including the back midline, the mouth line, the rear arc and the corresponding bottom line.


     

    The first half of the 2. picture: the center of the center line is the center of the center line of the middle back of the template, and the template is rotated to the back midline and tangent to the broken line, and then the middle line and the base line are depicted.

    (see chart 3)


    3. amendment

    (1) rear arc A upper section F: Main correction width, so that the width of the model joint is consistent with the width of the last face.

    Add the template over the broken line to the back arc.

    B lower segment: compare the difference between the middle point of the front face, the most concave point to the most convex point of the back arc, the distance between the concave point and the two distance on the template.

    The template is shorter than the last part in the lower arc section, and the template can be 10MM 12MM shorter than the last one.

    C will connect the upper and lower segments smoothly, and the bending changes of the new rear arc should not be too large, otherwise the quality and efficiency of the zippers will be affected.

    (2) bottom mouth: smooth connection bottom mouth, make inside and outside bosom.

    (3) front end of the system: the front end of the system is turned into an arc.

    4. let's stretch the weight (see Figure 4).


    The 12MM 16MM tension is released from the tip of the front to the back arc.

    Explain:

    1. the distance between the front end of the model and the bump of the rear arc is shorter than that of the last surface, which results in a tight place.

    The first zipper should be pulled out before stretching, and then the zipper should be closed before serving.

    2. the concave point of the front to the back arc of the template, the distance between the bumps is shorter than that of the last surface, and must be stretched by force so that the material can be extended before serving the last.

    3. during the trial production, if the front end of the system is reduced a lot, the step 1 should be adjusted.

    If the front end of the system does not go down, it should be adjusted to take steps 1 or 3.

    After the upper arc is not acceptable, step 3 or 1 and step A should be adjusted.

    It should be adjusted to take steps 3 or 2 and step 4.

    • Related reading

    Method For Measuring Foot Shape

    Shoe material excipients
    |
    2008/8/11 10:05:00
    41861

    Forming Process Of Footwear

    Shoe material excipients
    |
    2008/8/11 10:03:00
    41751

    Introduction Of Special Stitching Method

    Shoe material excipients
    |
    2008/8/11 10:01:00
    41744

    Michelin Extends Its Tire Technology To The Field Of Sports Shoes

    Shoe material excipients
    |
    2008/8/11 10:01:00
    41753

    Rule Of Foot Type

    Shoe material excipients
    |
    2008/8/11 9:59:00
    41809
    Read the next article

    Production Of Fine Rubber Powder By Air Turbine Refrigeration And Low Temperature Comminution

    The technology can be used to produce waste rubber into fine reclaimed rubber powder. It has wide application scope, can be used to produce modified asphalt and lay high grade road. It can be directly mixed into high-grade rubber products with high quality requirements, instead of a considerable amount of raw rubber, so as to reduce cost, save expensive rubber raw materials, and improve the mechanical properties such as fatigue strength, shrinkage and fluidity of rubber products. The whole equip

    主站蜘蛛池模板: 免费a级毛片无码av| 夜鲁鲁鲁夜夜综合视频欧美| 国产又大又粗又猛又爽的视频| 亚州日本乱码一区二区三区| 五月婷婷一区二区| 杨幂最新免费特级毛片| 国产精品va在线观看无| 亚洲人成人网站在线观看| 亚裔玉videoshd和黑人| 日韩精品久久久免费观看| 国产在线观看色| 久久久久亚洲精品无码系列| 老色鬼久久综合第一| 成人区人妻精品一区二区不卡网站| 又爽又黄又无遮挡的视频在线观看 | 制服丝袜怡红院| www.日本在线视频| 特级欧美视频aaaaaa| 国产色视频网免费| 亚洲ⅴ国产v天堂a无码二区| 久久波多野结衣| 日本久久久久中文字幕| 又大又硬又黄的免费视频| juy639黑人教练君岛美绪| 欧美高清在线视频在线99精品| 国产精品国产三级国产专不∫| 亚洲2022国产成人精品无码区| 韩国xxxx69| 性欧美大战久久久久久久久| 国产精品永久免费| 亚洲AV色香蕉一区二区| 韩国女主播一区二区| 成年1314在线观看| 91黑丝国产线观看免费| 欧美xxxx做受性欧美88| 国产仑乱无码内谢| 一本色道久久综合亚洲精品| 毛片色毛片18毛片美女| 国产成人性色视频| 一道本在线视频| 欧美日韩福利视频一区二区三区|