Brief Description Of Rubber Processing Operation Procedures
I. safety regulations for artificial rubber cutting
One
Before operation, carefully check oil level, electric limit switch, pmission device and hydraulic system, keep the glue cutting machine in good condition, and the glue cutting machine must be equipped with series double switch device.
Two
And trolley pportation shall not exceed the limit specified by our factory.
Three
It is necessary to use iron hooks when cutting glue.
Four
When the glue is placed, the raw rubber can be activated before starting. After starting, the rubber block should be prevented from popping and hurting people. No part of the body should be crossed over the cutter line when cutting.
Do not use hand and foot to promote raw rubber when cutting glue knife.
Five
It is forbidden to cut glue continuously, prohibit cutting cold, hard raw rubber and sundries.
Six
When the equipment is running, it is forbidden to crawl or lie down on the conveyor belt.
Seven
When facing the blade of the knife edge, the cutting knife raises the wooden block and can be carried out after cutting off the power supply.
Eight
When discontinued, the cutter should be lowered, cut off the power supply and clean up the site.
Two. Safe operation procedures for automatic glue cutting.
One
Observe the safety regulations of artificial glue cutting.
Two
The automatic glue cutting personnel should contact the scale personnel of the corresponding machine before carrying out the operation.
Three. Safety operation rules for gel breaker
One
On the belt, strictly prohibit crossing, crawling, lying and waiting, so as to prevent hurting people.
Two
The conveyor belt must be conveyer. The conveyor belt must be stopped when it is stopped and stopped. When rubber is conveyer, it is necessary to prevent the rubber from being crushed.
Three
When the gel is broken, it is necessary to prevent the rubber from popping and hurting people. When the roller is not easy to roll down the rubber, it must be handled with special tools.
Four
And others
((
Safety operation regulations for open rubber mixing machine.
Four.
XHM
Safety operation rules for series mixer
One
Before working, wear protective clothing and special respirator and respirator.
Two
Before running, it is necessary to check the rotors in the mixing room to ask if there are any sundries, top and bottom bolts, turn over doors, meters, signal devices and so on.
Three
Before you drive, you must send a signal. You can only drive when you hear that it is confirmed that there is no danger.
Four
Before placing the material, close down the top bolt first and put the film in one by one. Strictly prohibit the feeding at a time. The powder should be put lightly to light, and the carbon black bag must be delivered downward to the wind pipe.
Five
During the operation of the equipment, it is strictly prohibited to view the probe in the mixing chamber. When watching, you must hook up the feeding port with the hook, lift the top bolt and insert the safety pin before you can view it.
Six
During operation, it is found that debris must be shut down when it goes out of the mixing room or fails.
Seven
In case of a sudden stop, the upper bolt should be lifted and inserted into the safety pin to open the lower plug, cut off the power supply, and turn off the water and steam valves.
If you use manual rotary coupling to discharge material, pay attention to cooperate with each other and strictly prohibit driving with materials.
Eight
Upper top bolt is extruded with rubber.
(
card
)
When you live, you must stop.
Nine
The material leaking out of the bottom bolt is not allowed to be pulled by hand, and must be removed by iron hook.
Ten
When operating, it is necessary to stand outside the feeding and turnover board, and not to stand in the lower part of the discharging port.
Eleven
We should be careful when using materials and vehicles. When pporting materials, we should gently handle them and prevent them from hurting people.
Twelve
It should be connected with the next process by signal.
Thirteen
After parking, insert safety pin, close the flap door, lower the top bolt, open the lower plug, close the wind, water and steam valve, and cut off the power supply.
- Related reading
Basic Thinking And Technological Process For Processing Cattle Soft Upper Leather
|- Shoe Market | Air Force 1, City Color Matching "What The NYC" Shoes Preemptive Preview
- Bullshit | Different Designs Of Ma Haimao'S Blouses On The Top Of The Shirt.
- I want to break the news. | Creative Group "Sued" Hard Core Us Tide Off-White Trademark Infringement Has Exposed A New LOGO Design.
- Fashion Bulletin | German Famous Shoe Shop Asphaltgold Shoes Appreciate
- Fashion shoes | Philippine Dong X Joint NMD Hu Shoes "Look Within" Orange Red Version Debut
- I want to break the news. | Bulgarian Designer Kiko Kostadinov Photo Series Debut
- Shoe Express | Vans X HAVEN 2019 Combined Shoes Series Comes Out, Highlighting Military Style.
- DIY life | HUMAN MADE X Verdy Jointly Published "Harajuku Day Festival" Series
- Shoe Market | New Brun X Slam Jam Joint 990V3 Shoes To Open Pre-Sale, Only 89 Pairs.
- Bullshit | Champion X Dr. Seuss 2019 Joint Capsule Series Released, Full Of Children'S Fun.
- YOUNGOR Brand Changes Five &Nbsp; &Nbsp; Raise Profit Margin.
- For Two Days, 50 Thousand People Arrived At &Nbsp; &Nbsp; &Nbsp; Sales Amount Exceeded 10 Million.
- Cattle Enter The Country And Inventory China's Leather Economy
- How Can A Registered Trademark Be Pferred?
- New Children'S Clothing Must Be Cleaned Before Wearing &Nbsp; The Ph Value Of Clothing Formaldehyde Content Is Harmful To Children'S Skin.
- The Pressure Of Leather Production Enterprises Is Increasing, Leading To Higher Prices Of Products.
- How To Identify And Destroy Files?
- Stable Growth Of Leather Industry In 1-2 2010
- Zou Yanjian: A Game Of Chase
- Written Rules For Compensation Trade Contracts