Ironing Process For Silk Garments

Ironing is

A very important process in garment production. This article introduces the saving of ironing in the chest and waist.

1, ironing the chest

Let's start with the skew chest. Explain the process of pressing the silk dart. First, roll the clothes piece off the pavement and turn it back to the body. The tip is on the right, and the scalding must be hot from the tip of the province, so that the wide silk thread can be pressed tightly.

First, tighten silk thread, and the provincial road needs to spray water.

The sprinkler area includes the entire province and 3 cm outside the provincial line.

From the beginning of the province, the head of the iron is slightly lifted. It is gently pported from the outside side to the outer side, and the inner side is lifted and suspended. The ironing area should not exceed 3 centimeters outside the province.

The iron should be hot. Run slowly. Light should be applied. When the iron touches the surface of the province, it sends out the sound of air and air. At this time, the fabric becomes soft.

The iron began to operate second times from the tip of the province. The head was still slightly lifted. The outer side exerts a little exertion, and the ironing gesture is gradually increased by light. The silk thread is normalized. When the iron is away from the provincial road, carefully observe the recovery of the shape and thread. At this time, the provincial road has not been scalded.

If the quality of the product is good, it can completely tighten the dart.

After the restoration of the province, the garment piece is then expanded, and the provincial road is moved to the steamed bread mat, and the tip is on the right side.

We start with the index finger, middle finger and ring finger of the left hand from the tip of the province.

(two points should be noted:

First, the fingers should be pressed gently on the seams. If they are folded, the seams will be sewn and then pushed away with fingers.

The two is to straighten the provincial road. At the same time, use the front end of the iron to follow the three fingers to burn the province down. The gesture is Ping Ping and scalding Duan Tangping.

No gestures can be made to correct the dart.

Fold down the dart and straighten it down. Cover the dart with a hot cloth. Spray a little water with a hot iron. Press it flat. Press the iron on the middle surface and press it slowly on the dart.

Ironing must be done with hot cloth, dry road, hot pad (steamed bread mat).

Here are three ironing techniques.

(1) in the process of pressing the dart, the amount of water should be controlled and not repeated.

Many times it is heated and ironed. It will become soft and lose its original elasticity and gloss.

(2) to ironing dart with steamed bread mats. The reason is that the road is in the process of high temperature, stereotyped and ironing, and it is necessary to protect the three-dimensional effect of the satisfactory chest.

(3) during the whole process of ironing the dart, the ironing is always used for ironing. The hand-held ironing technique is aimed at restoring the threads of the provincial thread, pressing them tightly and pressing them.

A province is like a gentle line. Besides its function, it can not add bending to clothing.

The side effects of wrinkling, irregularity, clothing and so on. A series of techniques for pressing the dart are to achieve this effect perfectly.

There are two kinds of phenomena that can not be blanked by the provincial road and the width of the provincial road.

After the chest is pressed,

It is necessary to finish pressing and ironing. Put the piece of clothing on the pad on the table. The iron starts from right to left with a light hanging gesture. The light iron is the iron that is pressed on the clothes piece to press. It can not push the garment piece. The aim is to restore the wrinkles of the piece of clothing and smooth the wrinkles.

Because the parts of the provincial highway are ironed with high temperature, the fabric is contracted, and the ironing is allowed to synchronize all parts outside the provincial road.

The iron is divided into two parts, the center of the chest is divided into the inner and outer parts. First, press the shoulders, chest, neckline and the mouth. The iron should be slipped and slipped on the slide.

When the chest is pressed, the left breast must be lifted suspending. The purpose is to effectively protect the stereoscopic effect of the garment piece. After the inner part is ironed, change the shoulder, armhole and slot position on the outer side. When the outer chest is pressed, the medial chest position should be lifted suspending.

The center part of the inside and outside is ironed and ironed at any time during ironing, leaving no trace of blanching marks. There is a certain heat temperature after the clothes are pressed, and must be placed carefully.

Because hot clothing is the most susceptible to wrinkling.

There are two ways to place the front part of the shirt. One is to press the garment piece directly into the middle of the chest according to the inside and outside side of the ironing sheet, and fold it on the table board. The two is to spread the clothes flat on the table board, and put the inner chest on the steamed bread pad. This three-dimensional form can effectively protect the chest shape of the garment.

2. iron waist saving

Waist saving is the eye-catching part of clothing chest. It must be carefully ironed and displayed.

The first step is to ensure that the garment piece is cut across the waist to save the folds and lay straight, the neckline is on the right side, and the outer side of the iron is ironed to save the line and not to run outside the province.

High temperature water spray from the top of the province can be used to press the provincial road once again, so that the fabric of the provincial road will be heated and soft.

The second step is to press the iron according to the first running direction. The speed will slow down and the strength will increase.

When the iron is pported to the waist section, the left hand uses the thumb and index finger to force the 3.5 centimeters below the waist line to pull away.

The iron is pushed and pulled with the gesture.

Then the iron is pferred to the left hand, and the right hand uses the same gesture to pull and unpick the 3.5 centimeter position above the waist line. The iron will also pull back this segment and turn the iron to the right hand.

The second step is to press the ironing process at one go, the pportation capacity is in place, and the waist is saved to be pressed into two middle flat shapes.

The waist joints are naturally forced.

What is the standard of elongation in the middle section of the province? According to the principle that the arc is longer than the straight line, the waist is saved.

The degree of elongation is much larger, but vice versa. The difficulty is that the drawing line is straight wire thread. It is too small to stretch. The force is too small to be pushed away. Therefore, we should be careful when pressing this part. We should increase the capacity of the hand slowly, depending on experience.

Through the two push and pull.

The middle section of the province has a distinct wavy shape. It indicates that there is a certain elongation. If you drop the provincial road down and observe it, the provincial road is more relaxed than before. This means that it achieves the push and pull effect.

The process requirement of this part is more relaxed. It can make the clothes of chest, waist and buttocks clean.

The third step is to save the waist and scald it.

This process must be filled with steamed bread.

In order to protect the stereoscopic shape of the waist, the range of ironing must be limited to the provincial road.

Unfold the garment piece, save the waist and spread it on the steamed bread mat. The upper part is on the right side, and the provincial road is straight.

From the beginning of the province, use the left index finger, middle finger and ring finger to fold the section of the provincial road one by one. At the same time, you can touch the surface with your fingers. No seams can be generated. The iron is followed by a slight lift and flat press. The blanching is straight and hot.

After the waist is saved, ironing is done. The sheet should be ironed. The ironing method has been mentioned in the pressed chest shoulder.

Waist saving will not be used alone in clothing.

It is often used at the same time as the horizontal chest and oblique chest. Therefore, the front clothing with waist saving is bound to have oblique and pverse chest.

We take the oblique chest and waist saving as an example to explain the ironing process of the two provinces. It can be understood as the successive ironing of two provinces on a piece of clothing, and now the clothes with slanting chest and waist saving clothing are ironed. Because of the combination of two provinces, the garment piece has formed a three-dimensional shape, so we need to carry out three dimensional ironing.

When the iron is pressed, the chest is high and the waist is saved to divide into two parts: inside and outside, shoulders, chest and waist.

The outer part of the buttocks should be lifted suspensely, otherwise the inner part should be hung and scalded, so as to maintain the curve and three-dimensional shape of the garment piece.

Ironing the head, the inner part and the outer part of the iron, run smoothly on each part of the garment piece, press the chest round and round the waist, and press the waist clothes.

After finishing, the clothes must be placed according to the way laid before. After the right and left pieces are ironed, they overlap the two pieces.