Introduction To The Method Of Making Rabbit Skin

After the development of the Rex Rabbit in the vast rural areas of China, a small amount of rabbit skin is needed in the family.

The equipment is simple, the method is simple and the medicine is easy to purchase.

The method of making rabbit skin that is suitable for farmers' production is introduced as follows.

1. soaking water to soften home made rabbit skin, and generally maintain room temperature at around 20 C.

The rabbit skin after air drying should first use a blunt knife to shovel the oil film and residual meat on the skin, then immerse it in clean water for 1-2 days, so that the rabbit skin can be recovered to the fresh skin as much as possible.

2. degreasing method is the key step to remove the fat from rabbit skin.

The traditional method is to use sodium carbonate solution (2 grams / liter) to spread on the board, try to avoid the liquid contact with the wool surface, so as not to prevent rabbit hair from crisp, and wash it with water for 10-20 minutes.

Then use the detergent powder (2 grams / liter) to mix the warm water and soak the skin. Wash it with water after 10 minutes.

3. after pickling, cleaning, and resurgence.

It can be pickled with salt.

With 20% mirabilite (sodium sulphate) and 25% rice flour, the liquid was soaked for 1-2 weeks in comparison with 1:6-8 (with Humidity Gauge).

Rice flour is made of glutinous rice flour or rice flour. Avoid using flour instead of flour. Although flour can be fermented, it can be easily sticky.

After the rabbit skin has been injected with nitric acid, it should be turned 1 times a day to make the cylinder temperature uniform.

The leather should be removed in a timely manner and dried for 1 times while the skin is half dry. After finishing with a small amount of finishing, the fabric has short plush and smooth feet, soft handle, soft bones, elasticity and natural luster.

Avoid excessive shrinkage of the skin plate.

4. finishing work, after the pickled, dried and dried rabbit skin, use the knife to repair the hard edges, then rub the skin to soft ripe, then take the rice flour.

Nitrite tanned fur, such as the phenomenon of "nitrification", that is, the Glauber's salt in the skin is dissolved by water wet, so that the skin plate is bonded and hardened, showing the appearance of raw leather, and even the phenomenon of hair removal. It can be treated with 250 grams of chrome alum, 250 grams of salt and 25 grams of sodium carbonate.

First use hot water 2.5 liters to dissolve chrome alum, cooling; warm water 1 liters dissolved sodium carbonate; cold water 1.5 liters dissolved salt.

Then slowly add the sodium carbonate solution into the chrome alum solution, stir it with the stick, and add the salt solution.

Evenly spread the mixture on the skin plate with clear water wetted, then place the back plate on the stacked plate for 4-5 hours, and repeat the 2-3 times until the mixture is soaked through the skin.

Then wash the skin with water, remove the salt and tanning liquid, dehydrate, flex, dry, rub, rub, rub and soften.

Five

Save the rabbit skin that has been processed and patted with rice flour. After several days of exposure, the residual fat can be volatilized and the odor is eliminated. Proper amount of camphor is used to prevent moth. It is a tussah silk fabric that is made of hand tools and has natural knot patterns and pearl luster.

Because of its rugged style, richness, firm texture, and soft and full handle, it is dyed with a mixture of dyed wool and raw wool. It is blended into a mixture of woolen yarns.

Fabric organization is also a twill weave on top two of two, with a grain inclination of about 45 degrees.

The materials used are mainly fine wool, which is mainly made of grey, rice and coffee, and suitable for spring and autumn wear and trousers.

It also has viscose, polyester or silk blended with wool.

Use cloth to wrap up the summer.

The products can also be processed into various fur products.