Design Of Shoes In Shallow Area

Shoes in the shallow area are the simplest belt shoes.

In the early stage, the shoes in the shallow area were made into "gourd shaped" shoes, and a shoe table was designed to assemble shoes and laces.

Now it has been simplified to put shoelaces directly on the shoe ends.

There are 3 different types of shoelace.

The first one is the shoelace position. The shoe lacing is more decorative than the functional point near the V point. Instead of opening and closing the shoes, the shoelace is relatively narrow. It often takes 8 to lOmm and the end of the shoelace is relatively short.

The laces of color picture L-18 are fixed, and the positions are relatively close.

The second is the position of the shoelace, which is located at the E point. The main function is to increase the ability of the shoe to hold the feet. The shoelace is wide, and it is usually taken at 12~14mm. The end of the shoelace is longer. See the color picture L-20, the shoe has a shoe table, and the wider shoelace is installed on the shoe table.

The third is the position of the front swallow bone in the foot, which is both decorative and functional. The width and the design of the shoelace are different. The wide shoelace can reach 40mm, and the length changes flexibly. See the color picture 1-3., this is a wide laced product, color picture L-19, shoelace is not too wide, and there is a bow decoration on it.

The shoe drill belt can be matched with all kinds of shallow shoes, so long as the appearance is coordinated and the function is perfect, it will be welcomed.

1. design of shoes in round mouth area

As shown in figure 3-4-1, we first design round shoes according to the design requirements of round shoes.

Because the shoelace is relatively long, the break position is usually designed under the shoelace.

Position the vertical line of the back midline at E point.

The width of the shoe belt is designed before the E point, and the vertical line of the back midline is also made. The general shoe drill is designed into straight strips.

The position of the middle of the back should be increased by 5mm as the center line of the shoe drill.

Why rise?

Because women's shallow mouth last round is small, the actual circumference of the foot is reduced by about lOmm, and the increase of 5mm is to lengthen the lOmm of the shoes and meet the needs of the circumference of the feet.

For the shoelace in the front tarsal position, it is also necessary to increase 5mm before redesigning.

For shoelaces near the V point, the last metatarsal circumference is less than the 7mm of the foot plantar circumference, and only needs to increase 3.5mm.

Raising the design amount is only to solve the length of shoelace, and the specific tightness should be adjusted by the drill hole.

Design the width of shoelace from E point forward.

Shoelace is a free component, and it can move back and forth to suit the changes of the instep.

The traditional shoelace is wide and takes 12 to 14mm, giving people a strong feeling.

Modern people enjoy different tastes. They like to be thin and long. They usually take 10 to 12mm.

The width of the shoelace should be matched with the width of the shoe drill, so that the width of the shoelace is less than 1 to 2mm of the inner diameter of the shoe drill, so as to prevent the shoelace from being worn out when people wear out.

The length of shoelace is designed based on the position of shoelace and shoe drill.

In the past, the shoelace and shoe drill were fixed by the way of nail, so the length of the design was below 14mm, which is the starting point of the length of the shoe and the center point of the shoe. The tail of the shoelace is taken from 30 to 35mm below the center point.

The positions of the other 4 holes are distributed on both sides of the center hole, and the spacing is 5mm.

The total length of the shoe belt is 2 x (length +5) + tail length (30 ~ 35mm).

The shoelace of the shoe in the shallow area is often taken as a straight strip. It is designed perpendicular to the midline, so as to determine the direction of the shoelace and mark it with rules.

2., there are shoes in the shallow area of Baotou.

As shown in figure 3-4-2, the front end of the shoe has a Baotou, straight door, a shoe table on the back, and a shoe belt designed on the table.

The shoe brazing strip adopts the method of cutting the dark nail, and inserts the stubble of the shoelace and shoe braze skin into the incision, so the position of the incision can be in the position of 8 ~ lOmm below the entrance line of the shoe, and the quantity of the stubble is 8 ~ lOmm.

The total length of the shoe belt is 2 x (incision to last +5) + + 8mm (+ 30) 35mm.

The shoes are relatively long, so they can take the opportunity to join them.

3. design of shoes in small round mouth area

As shown in figure 3-4-3, the position of the mouth of the small round shoe is relatively high, and a shoelace leaning forward is equivalent to the position of the rear door, which improves the foot holding ability of the shoe.

The shoelace is relatively narrow, takes 8 to lOmm, the middle line raises 3.5mm, the incisional position is 8 ~ lOmm, the tail stays 15 ~ 20mm, hits 3 drill hole.