• <abbr id="ck0wi"><source id="ck0wi"></source></abbr>
    <li id="ck0wi"></li>
  • <li id="ck0wi"><dl id="ck0wi"></dl></li><button id="ck0wi"><input id="ck0wi"></input></button>
  • <abbr id="ck0wi"></abbr>
  • <li id="ck0wi"><dl id="ck0wi"></dl></li>
  • Home >

    Standard For Combination Strength Of Heels And Rear Sides Of Leather Shoes

    2010/10/11 15:44:00 70

    Combination Strength Of Rear Heel Of Standard Leather Shoes

    standard

    Leather shoe heel

    and

    Back bond strength


    1 theme content and scope of application


    book

    standard

    The test method for the strength of the heel and back side of leather shoes is specified.


    This standard applies to the heels of the heel and back bond (nailed) shoes, and is not suitable for the sole forming shoes with the following heel and outsole.


    2 Principle


    This method is based on the shoes and shoes on the special fixture. The tensile test machine is used to stretch the heel and the back of the shoe to the maximum load at a certain speed.


    3 sample


    3.1 the sample is made of 48h shoes.

    There should be no obvious defects in the test area, and no heel, crush or deformation should be followed.


    3.2 the bottom and rear heels are glued to the front and rear heels and shoes. Separate the bottom and heels before the test.


    3.3 30min must be placed at room temperature before testing.


    3.4 each sample should not be less than two pairs (the same batch of products).


    4 test equipment


    4.1 tensile testing machine.


    4.2 the special fixture for pulling and pulling is made up of two parts: clamping the heel clamp and clamping fixture for shoes (as shown).


    5 test conditions


    5.1 the tensile test speed of the tensile tester is 25mm/min.


    5.2 the ambient temperature is ambient temperature.


    6 test procedure


    6.1 install the pull and special fixture on the tensile testing machine. The clamp is installed on the upper jaw joint connecting rod, and the shoe fixture is installed on the lower jaw interface.


    6.2 adjust the tension tester pointer to zero.


    6.3 slide up the heel of the sample and clamp it on the shoe fixture.


    6.4 adjust the position of the shoe fixture so that the heel surface is visually measured. The heel is in the direction of the force of the tensile tester and the clamp is used to clamp the heel.


    6.5 boot and stretch until the heel is separated from the back and record the maximum load.


    6.6 if only the bonding strength is measured, stop immediately when the load reaches the product standard value, and check whether the heel is separated at 15~20s.


    7 test results


    7.1 the maximum load required for separating the heel and the back of the shoe represents the test result and is accurate to 5N.


    7.2 the test results for each shoe are indicated separately.


    7.3 the test result of any shoe in the sample is not up to the standard of the product standard, and the sample is not qualified.


    8 test report


    8.1 indicate that the tests are carried out according to this standard.


    8.2 sample number, name, specification, brand, production plant, heel height, heel material, shoe heel assembly form (adhesion or nailing).


    8.3 test results.


    8.4 test personnel and dates.


    Add-on:


    This standard is put forward by the Ministry of light industry of People's Republic of China.


    This standard is standardized by the China footwear industry standardization quality inspection center.


    This standard is drafted by the Scientific Research Institute of shoemaking industry of Ministry of light industry.


    The main draftsman of this standard: Yan Huai Dao.


    This standard refers to the Soviet Union standard TOCT 9136 "footwear, heel and pad pad strength determination method".

    • Related reading

    福建抽查休閑服裝 賽威達、萬杰隆等“榜上有名”

    Standard quality
    |
    2010/10/9 17:30:00
    69

    Fujian Province Casual Wear Product Quality Supervision And Spot Checks 30, 3 Failed.

    Standard quality
    |
    2010/10/6 14:14:00
    85

    Sichuan Clothing Sampling Inspection Formaldehyde Ph Excessive &Nbsp; &Nbsp; Failure Rate Of 38%

    Standard quality
    |
    2010/10/5 13:55:00
    64

    How To Maintain Good White Clothing Without Being Polluted?

    Standard quality
    |
    2010/10/4 20:57:00
    93

    The Ministry Of Industry And Commerce Approved The Implementation Of 60 Textile Industry Standards In October 1St.

    Standard quality
    |
    2010/10/2 10:35:00
    58
    Read the next article

    Gucci Is Also A Platinum Bag, Popular With Celebrities.

    You know something about luxury brands, you don't know Birkin bag, you know platinum packages. Platinum packages will cost hundreds of thousands or even millions of dollars. Birkin (Bo Jinbao), the international brand HERMES, has long been the focus of attention. But in 2011 Milan fashion week (Chun Xia), Gucci also had platinum bags.

    主站蜘蛛池模板: aaa毛片免费观看| 亚洲黄色在线电影| 啦啦啦www免费视频| 久久精品小视频| av在线播放日韩亚洲欧| 精品久久久久久久99热| 成人免费无毒在线观看网站| 国产精品天天在线午夜更新| 亚洲欧美精品一中文字幕| 91精品啪在线观看国产18| 视频一区二区中文字幕| 欧美日韩一区二区三| 好男人资源在线观看好| 免费看黄网站在线看| 久久午夜无码免费| 尤物yw午夜国产精品视频| 欧美三级电影免费| 国产欧美日韩在线观看无需安装| 亚洲一区二区三区欧美| 黄色黄色一级片| 日本一本在线视频| 啊灬啊灬啊灬快灬深一| tube欧美69xxxx| 欧美黑人巨大videos极品| 国产精品水嫩水嫩| 亚洲AV无码成人精品区狼人影院 | 丰满的己婚女人| 成人爽爽激情在线观看| 欧美性受xxxx| 国语对白清晰好大好白| 免费毛片a线观看| 97免费人妻无码视频| 男女啪啪永久免费观看网站| 在线精品小视频| 免费国产a国产片高清| 一级一看免费完整版毛片| 狠狠躁夜夜躁人人爽天天天天97| 国产视频网站在线观看| 亚洲精品国产精品国自产观看| 1313午夜精品久久午夜片| 曰批视频免费40分钟试看天天|