Basic Knowledge And Examples Of Skirt Pattern Design

The simplest way of skirt design is to divide the basic type of the two piece half skirt into several parts.

Usually, the skirt prototype is a simple half skirt.

But because it is made of paper, it can be folded and used.

The same paper can be used in four skirts with the front center line and the rear center line. Each piece is divided into two parts.

Or the same basic pattern, 4 pieces will be further folded to get 8 pieces; again the same fold, you can make 8 pieces into 16 pieces.

The prototype of the skirt can be divided into 6 pieces, which can be further divided into 12 pieces.

6 dresses are usually called "dresses".

This is a familiar style and can be designed by various styles of skirt.

In principle, each basic skirt type (standard skirt, straight skirt or full round skirt) can be divided into any number of cutting pieces, which can be the same or different.

If we make full use of the "line" or the basic type of change, we can get quite a lot of styles.

In fact, some shape lines are more suitable for multi chip designs.

For example, the molding line of full round skirt is warped outside.

Others are suitable for skirts with less cutting.

The style of the skirt is varied through slices, and the addition of loose weight between the cutting pieces can further increase the style of the skirt. The way of changing the skirt pattern also includes changing the use of the fabric texture, such as the skirt with a skew or cross direction.

Add all buttocks to all shapes and sizes of skirts, as well as many other specific cutting methods.

Example: simple multi piece skirt

Style A

The front middle stitches of 4 pieces of skirt are replaced by buttons that are arranged along the front centerline. Therefore, there is a need for a door (at least 3~4cm).

At the beginning of the picture, place the original position at the edge of the paper 4cm, leaving the width of the door open.

The welt can be single autocratic or linked to the front piece. The noodles should be at least 4cm more than the width of the door, that is, the buttonhole should be 7~8cm.

Usually, the welt is only cut on the fabric, like the turning angle, and does not need to be included in the cutting of the pattern.

Because this is a full round skirt, the side stitches will be less expensive when used for one-piece skirts or Western-style skirts.

In order to make the waist fit, if necessary, add a small province on the back center line. If it is to make a dress skirt, then there can be no provincial road, and all sutures should be straight lines, and the prototype is only suitable for the dress body.

The direction of the straight yarn is indicated on the pattern (SG).

Because the front piece has buttonholes, the center line should be straight before, and the rear piece should be straight from the middle axis of each piece, because this will increase the draping feeling of the skirt.

The general post middle suture is also almost straight, unless sometimes it is inclined to make the contour line more balanced, so that the skirt will expand evenly around the body, instead of being flat at the center line, but warping at the side seam. If the centerline is straight yarn, this will happen.

Style B

The 8 piece of skirt is made by cutting 4 pieces of skirt into two halves from the middle.

First, draw the front and back parts of the prototype skirt prototype, then fold each piece as if it were a straight yarn to mark.

Sometimes a small part can not be fully folded, but it doesn't matter.

The 1/4 round skirt prototype is also used in this type.

It uses the advantages of the prototype skirt prototype, that is, having a standard geometric shape, not necessarily a part of the circle.

The widened bottom pendulum (over the original 160cm) can start from the hip line or the lower point (the dotted line).

Each skirt is still straight in the middle.

Style C

Divide 6 pieces of skirt into twelve pieces.

In fact, only the front and rear sides are used, because the front and back pieces are half sided.

Since it is a fully round skirt, a small province should be provided for the tight waist of the skirt.

The center of the skirt is straight yarn.

This type of skirt has a low swing width of about 2.45m, but a large number of skirts and 12 suture =24 stitches, so the width of each piece is generally very small, that is, 3~4cm.