Analysis And Design Of Shoe Template

< p > variant is the commonly used design method in < a target= "_blank" href= "http://www.91se91.com/" > shoes < /a > design, that is, on the basis of prototype products, through a series of changes, so as to change the style structure of shoes, and increase variety.

The commonly used variant method is to change the shape of the last shape, change the structure, change the appearance and position of the components, and change the use of auxiliary parts.

< /p >

< p > 1, < a href= "http://www.91se91.com/news/index_x.asp" > shoe boots < /a > basic principle of style design < /p >

< p > (1), lines should be simple, bright and pleasant, but simple and not monotonous, bright and not exaggerated, pleasing but not farfetched.

< /p >

< p > 1, saving material and labor when considering mass production.

< /p >

< p > 2, design lines should not waste large pieces of shoe materials, but can not waste a lot of shoe materials due to a small amount of aesthetic effect.

< /p >

< p > (two), the specifications of the shoes are suitable for the market requirements, and pay special attention to the general foot type suitable for the people in the sales area.

< /p >

< p > (three), the style and technology of design should conform to the economic principle of mass production.

< /p >

< p > 1, the design should emphasize the economic function. The styling should pay attention to the majority of people's choice of a href= "http://www.91se91.com/news/index_x.asp" > shoes < /a > psychology, to be universal, reasonable price.

< /p >

< p > 2, the design is simple and saves material.

< /p >

< p > two, shoe structure design should follow the rule of foot type < /p >.

< p > < a > href= > http://www.91se91.com/news/index_x.asp > > Gang > /a > there are many methods of structural design. However, no matter which method is adopted, the following technical requirements should be followed: the proportion of each part should be determined according to the rule of foot type.

If the position of the sample is not properly arranged, it will not only affect the appearance, but also affect the wearing.

For example: the back is too high, it will wear feet; too low and can not hang feet; the front Gang is too long, which affects the ankle flexion, the inside and outside sides are too high, will touch the ankle bone, cause the foot body discomfort (low waist shoes); the mouth door location is too small, not only difficult to wear out, but also easy to break when the last door is broken; the location of the door is too big to wear and has a loose feeling; to help the bread head too long, it will squeeze the toes; the front and back sides are inserted into the position, if not according to the foot type rule, when traveling, there will be some problems such as broken surface or broken skin.

Therefore, in the design, not only pursue beautiful appearance, but also follow the principles of foot type, comfort of wearing and the life of shoes.

< /p >

< p > three, shoe line should cater for the last body head tone < /p >.

< p > the last type is generally changed at the front part of the last, while the posterior part of the metatarsophalangeal joint is generally unchanged. In addition to the height last (because of the difference between the last and the lower waist last), the last head has the following basic shapes: < /p >

< p > 1, round head (thick and round); < /p >

< p > 2, small round head (with a circle smaller than round head); < /p >

< p > 3, pointed tip (tip shape); < /p >

< p > 4, big square head (Square last, the last face has two kinds of styles: no /p).

< p > 5, small square head (square corner is smaller head shape, last face has two kinds of styles: no /p).

< p > 6, inclined head (head shape outward waist tilt); < /p >

< p > 7, flat head < /p >.

Less than P, the geometric shape of the last body head has their own unique keynote.

In line design, line processing should cater for the keynote so as to achieve a consistent effect.

For example: < /p >

< p > 1. round head: the tone of this shoe last type is circular arc, requiring the contour of the front part should be based on the arc line. For the wider circular arc type, the last face of the metatarsophalangeal part is relatively flat, so the contour of the parts near the part can be used with arc lines, which will produce a rich aesthetic feeling.

< /p >

< p > 2, pointed head: this kind of < a href= "http://www.91se91.com/news/index_x.asp" > shoe last < /a > head type keynote circle and straight.

The contour of the front part is straight and vertical. It requires some circles to make the lines prominent.

< /p >

< p > 3, square head: the head shape of this shoe last is square and straight, so the outline line of the shoe should be straight from the front of the shoe last.

For example, the upper Baotou line, the contour of the door and the contour of the front shoe cover are ideal for straight line processing. < /p >

< p > 4, flat head: this type of shoe last has the name of thin and thin, so the arc in the keynote is less, and the contour line of the front part is straight and square. < /p >

< p > as mentioned above, the characteristics of shoe last and vamp style must be harmonious.

The bottom curve of the shoe last must also be suitable for the shoe type. However, a shoe last can also allow a considerable "a href=" http://www.91se91.com/news/index_x.asp "vamp" /a to change and retain its original characteristics.

< /p >

< p > three. Shoe sample design should consider material and process < /p >

< p > shoes and shoes are made of various materials and methods of manufacture. However, materials and manufacturing processes should be considered in designing each product, because the properties, characteristics and elongation of various materials are different, especially when the upper side of the shoe is turned into a shoe shaped surface under the action of force, and the thickness of the upper is included in the upper, and the middle and bottom of the main heel, the inner Baotou, the sole of the sole, and the semi insole.

As a result, the positions of the parts are obviously shifted. They are not the size of the original design, so the size of the upper is not equal to the size of the shoe. The actual size of the shoe is larger than the size of the upper.

< /p >

< p > to ensure the size of the parts required for the shoes, we should pay enough attention to all kinds of materials in the design of the sample while the shifting and changing rules in the process of stretching must be dealt with in some parts for proper adjustment and control.

The parts of each part should be smaller than the actual size of the shoes 2mm? 4mm, so that the design dimensions can match the shoe size.

< /p >

< p > four, line and fat and thin feeling < /p >

< p > shoes should be fat and thin. This is because the script is fat and thin, but from appearance, people always want to be thin and good-looking.

< /p >

< p > for the thinner shoes, the upper part should be arranged less.

And the lines can be bent as much as possible, which will give people a sense of fullness.

< /p >