• <abbr id="ck0wi"><source id="ck0wi"></source></abbr>
    <li id="ck0wi"></li>
  • <li id="ck0wi"><dl id="ck0wi"></dl></li><button id="ck0wi"><input id="ck0wi"></input></button>
  • <abbr id="ck0wi"></abbr>
  • <li id="ck0wi"><dl id="ck0wi"></dl></li>
  • Home >

    Analysis Of Causes For Dissatisfaction Of Injection Molded Products

    2008/8/11 9:47:00 41803


     

    The main reason for the dissatisfaction of injection products is lack of material and injection pressure and speed (including pressure caused by resistance).

    It may be caused by the following reasons:

    1. reasons for injection molding machine:

    If the plasticizing quantity or heating rate of the machine is not fixed, the plasticizing quantity and heating power should be selected.

    The wear and tear of the screw and the barrel or the rubber head cause the actual charging modulus not to be returned; the heating system failure of the thermocouple or heating ring causes the actual temperature of the material barrel to be too low; the seal element of the injection cylinder causes oil leakage or reflux, and can not reach the required injection pressure; the small internal hole of the nozzle or improper adjustment of the nozzle center degree leads to excessive resistance and pressure consumption.

    2. reasons for injection mold:

    1. the local or overall temperature of the mold is too low to cause difficulty in feeding.

    2. the distribution of mold cavity is unbalanced.

    The thin wall thickness of the parts results in excessive consumption of pressure and poor filling.

    The whole part or part of the wall thickness should be increased, or the auxiliary flow or gate should be set up near the underfill place.

    3. the flow path of the mold is too small to cause pressure loss; when too large, there will be weak glue; too rough will cause dissatisfaction.

    The size of the runner should be appropriately set, and the proper arc pition should be applied to the pition between the main stream and the shunting Road, the gate or the turning point.

    4. mold exhaust is bad.

    The material entering into the cavity is filled with dissatisfaction due to the obstruction of the gas pressure which is not enough to discharge.

    We can make full use of the slot exhaust of the screw or reduce the clamping force, and use the parting surface to exhaust. If necessary, we must set up the exhaust channel or air hole.


     

    • Related reading

    Formulation Of New Neoprene Adhesive

    Shoe material excipients
    |
    2008/8/11 9:46:00
    41776

    Common Problems In Injection Molding After Adding Color Masterbatch

    Shoe material excipients
    |
    2008/8/11 9:46:00
    41780

    Matters Needing Attention In The Use Of Adhesive Products

    Shoe material excipients
    |
    2008/8/11 9:45:00
    41775

    Main Functions Of Rapid Prototyping Technology

    Shoe material excipients
    |
    2008/8/11 9:44:00
    41778

    Process Characteristics Of Thermosetting And Thermoplastic Reinforced Plastics

    Shoe material excipients
    |
    2008/8/11 9:43:00
    41773
    Read the next article

    Improving Dyeing Properties Of Synthetic Microfiber Leather With Suitable Dyes

    Dyeing technology of microfiber synthetic leather is developing rapidly. The finishing finishing technology of leather has been applied to microfiber synthetic leather in the market. However, most of the microfiber cloth is white. Before the skin is applied to the synthetic leather, it must be coloured to achieve the super simulation effect. Because of the few active groups on the microfiber fibers, there are a large number of carbon chains and amides in the middle of the molecular chain.

    主站蜘蛛池模板: 国产在线观看麻豆91精品免费 | 亚洲国产成人精品无码区二本| xxxx国产视频| 美女免费视频一区二区三区| 日本天堂视频在线观看| 国产午夜亚洲精品国产| 久久文学网辣文小说| 青草青草视频2免费观看| 日本高清成本人视频一区| 国产免费爽爽视频免费可以看| 久久亚洲色www成人欧美| 里番acg※里番acg本子全彩| 无码毛片视频一区二区本码| 国产freesexvideos性中国| 中文字幕亚洲欧美日韩高清| 精品无码国产一区二区三区av| 成人AAA片一区国产精品| 免费看黄a级毛片| freesexvideo性欧美医生护士| 激情在线小说图片视频区| 国产高清视频一区二区| 亚洲国产精品一区二区久久| 国产人成精品香港三级在| 日本哺乳期xxxx丨| 和桃子视频入口网址在线观看 | 99久久国产综合精品五月天| 日本高清中文字幕在线观穿线视频| 国产三级精品三级在线观看| 三年片在线影院| 爱情论坛免费在线看| 国产精品冒白浆免费视频| 久久精品无码一区二区日韩av| 超薄肉色丝袜一区二区| 影音先锋男人站| 亚洲欧美精品成人久久91| 日本免费网站视频www区| 日本中文字幕有码在线视频| 再深点灬舒服灬太大了添网站| 97超级碰碰碰碰久久久久| 有人有看片的资源吗www在线观看 有坂深雪初尝黑人在线观看 | 精品人妻一区二区三区四区|