• <abbr id="ck0wi"><source id="ck0wi"></source></abbr>
    <li id="ck0wi"></li>
  • <li id="ck0wi"><dl id="ck0wi"></dl></li><button id="ck0wi"><input id="ck0wi"></input></button>
  • <abbr id="ck0wi"></abbr>
  • <li id="ck0wi"><dl id="ck0wi"></dl></li>
  • Home >

    What Are The Techniques In The Process Of Shoe Design?

    2010/3/26 20:54:00 50

    Vamp Design

    When the standard upper part of the upper part of the upper part is bent to form a curved surface, only a straight middle line style can be used to make a single piece of shoe face part.

    Therefore, the flattening process involves straightening the bent line.

    Obviously, there are only a few references to the process, so beginners feel that the process is daunting and not surprising.


     

    fundamental theory


     

    In the surface design, the center line must be straight to ensure that the overall pattern is cut out.

    But how should this process be carried out?

    In this part, many styles of cutting are taught to put the upper part of the standard pattern with the center line of the curved surface placed on the straight line which will become the new midline, place the center of the curved line below the straight line, and then place the end part of the two lines above the straight line.


     

    Two alternative ideas are shown.

    Locating line segment

    One

    The lines are similar in size.

    Therefore, people will think that when the vamp is molded, the pressure applied to each area is the same.

    Line

    Two

    It shows an alternative location that is far away from the center of the line and away from the toes.


     

    However, when a straight line is positioned, it is easy to overlook a very important problem if we only pay attention to the toe area and the midline of the curved surface, and this problem will become more obvious later.


     

    Design line

    AB

    When the shape has to be changed, the length must remain the same, because the edge of the toe should be stitched to the boot of the design line.

    The toe area needs to be supported or arched to ensure proper width above the toe.

    Because this usually shortens the molding edge, it may be necessary to compensate for it by backing or arching the lower part of the rear edge of the shoe.

    We will explain why this causes problems.


     

    general rule


     

    In fact, we can set up some general rules that can be applied to many styles of shoes for the flatten process.

    The process can be summarized as follows.

    Three

    One step.


     

    One

    Line segment

    C-A:

    Determination point

    O

    The location of this design line (

    A-O

    The part will be arched without changing parts.

    O-B

    Meeting and line segment

    X-Y

    Rendezvous, then determine its location and set it as a new central line.


     

    Two

    Line segment

    A-B:

    From existing line segments

    A-O

    Intercept new line segments

    A1-O-B


     

    Three

    Line segment

    B-C:

    Deciding the supporting point

    P

    The location here delineated a new toe area forming the sideline.

    The side line and the existing line segment

    C-B

    blend


     

    When the boot surface is flattened, the whole cut surface is produced by the common method, and the center line is cut by hand.

    XY

    As a folding line, or as a mirror line, if the computer aided system is used (

    CAD

    Words.

    Steps in

    Three

    Processing side port

    C-B

    The external method also handles the inner edge.


     

    The following steps will be introduced in more detail.

    One

    ,

    Two

    and

    Three

    And explain its working principle.


     

    In step one,

    Ninety

    When measuring azimuth, point

    O

    To the centerline

    X-Y

    The distance must be in line with the standard case.

    O

    To the midline of the curve

    C-A

    The closest point is the same distance.

    This is because the side stitches of vamp.

    A-O-B

    It is divided into two parts.

    Lower part

    OB

    The shape or position does not change. When it is connected with the boot part, there will be a green drawing line in the picture. This line controls the position of the surface, or rather, it controls the area or boot of the leg when the surface is molded.


     

    For example, if in style,

    O

    Point distance centerline

    X-Y

    Specific surface line

    C-A

    Near, the upper barrel can not be properly positioned when molding.

    If

    O

    A little higher will lead to incorrect angle of the boot relative to the ground.

    keep

    O

    The distance from point to center is a very important problem. If people only pay attention to the middle line of shoe upper when locating the new middle line, this problem is easy to be ignored.


     

    The angle of the line segment is even more difficult to determine, although the angle problem is not particularly critical.

    Straight line

    O

    The gap between the front and the center line.

    A

    No more than

    5-6

    Millimeters, generally

    3-4

    About millimeters.

    From the toes part, the line falls to the gap below the centerline.

    B

    It should be clearer than the gap.

    A

    Slightly larger.


     

    Step 2, new line segment

    A1-O-B

    Must and original segment

    A-O-B

    The length is equal.

    Remember line segment

    O-B

    There is no change, so

    A1-O

    Parts must be examined carefully.

    The segment of a boot tube.

    A-O

    Will be sewn into the upper.

    A1-O

    In the side line, therefore

    A1-O

    Any distance line segment within a length range.

    X-Y

    The distance must be in accordance with

    Ninety

    The original line is measured.

    A-O

    distance

    C-A

    The distance is the same.

    This will ensure that the "tongue piece" of the toe will be equal to the distance from the opposite side to the distance from the shoe side according to the original standard process.

    Any difference here will change the fitness of boots.


     

    In step 3,

    P

    The location of the dots is not important.

    It should be about the line segment.

    X-Y

    In the middle of the molding line, in the line segment.

    X-Y

    Go through the lower part of the center line of the toe of the shoe.

    take

    P

    Point as support point, using line segment.

    C-A

    New centerline near toes

    X-Y

    Above distance, line segment.

    C-B

    Move down.

    Then the line segment and the original line segment are used.

    C-B

    Mix together.


     

    from

    P

    After the support, the toe may look a little longer, but in fact, the molding line is shortened.

    Support points only.

    P2

    In order to ensure that its length is unchanged, but the upper part of the front surface may be too long.

    Similarly, if support points are used

    P1

    The upper part usually becomes too short.


     

    As mentioned earlier, when the toe area moves downward, there is a tendency to shorten the molding line.

    This is not recommended because the rear edge of the upper can be turned.

    O-B

    Move back to the point

    O

    To become a line segment.

    O-B1

    Extending the length of the molding line will extend the length of the molding line in the wrong position.

    Line segments on boot

    OB

    It has not changed, but if you will segment the line

    O-B1

    Put it on, you will see what changes will happen in the centerline.


     

    What is the universality of rules?


     

    These rules apply to all sloping styles that extend to the instep of boots and shoes, and even in a slight preform design.

    Indeed, many

    Gibson

    Shoes and

    Derby

    Shoes will benefit from using the same boot.

    For example, using a straight line.

    XY

    From the point of forming

    O

    The absolute tension to the center line is much smaller than that of the ordinary black line.

    .


     

    Duplicate key steps


     

    Sure?

    O

    Point, draw a straight line.


     

    At point

    O

    A new line segment is set up without changing the distance between the distance center line measured at each length and length.


     

    Shape the toe area and move down.

    ,

    Mixing with existing molding edges.


     
    切記:形狀保持力是質量的最終指示器,沿組件款式中的草擬線復制標準尺度是聯系以上描述的展平過程和好的形狀保持力的關鍵因素。
    • Related reading

    Introduction To Bundle Like Microfiber Artificial Leather

    Shoemaking technology
    |
    2010/3/2 13:20:00
    99

    Italy Looks At China'S Leather Shoes Market

    Shoemaking technology
    |
    2009/9/9 17:01:00
    48

    Leather Shoes Factory Fire Equipment Is Too Crude, Workshop Is Burned.

    Shoemaking technology
    |
    2009/5/27 14:26:00
    42116

    Footwear Export Data Have Been Counted Out.

    Shoemaking technology
    |
    2009/5/27 14:19:00
    42075

    Shishi Eight Shoe Enterprises Embark On The Road Of Self Export

    Shoemaking technology
    |
    2009/5/22 15:48:00
    42109
    Read the next article

    A Brief Account Of The Total Amount Of Leather Exports To Various Countries In Pakistan

    Pakistan's leather exports to France, Germany and Switzerland amounted to $170 million, accounting for only 1% of the three countries' total leather imports. Pakistan exports leather to France $61 million, exports to Germany $106 million, exports to Switzerland $2 million.

    主站蜘蛛池模板: 国产精品国产三级国产普通话| 欧美老妇bbbwwbbww| 无限看片在线版免费视频大全| 国产对白受不了了中文对白| 亚洲av成人无码久久精品老人| 18美女扒开尿口无遮挡| 毛片大全免费看| 国内黄色一级片| 国产成人精品实拍在线| 亚洲免费在线视频| 1024视频在线| 最近中文字幕精彩视频| 国产成人无码精品一区不卡| 久久精品噜噜噜成人av| 高清伦理电影在线看| 日本在线观看中文| 国产一级一片免费播放| 中文字幕成熟丰满人妻| 美女爽到尿喷出来| 小小视频最新免费观看| 免费一级欧美片在线观免看| 99精品国产高清一区二区麻豆 | 亚洲日韩一区二区三区| 4四虎44虎www在线影院麻豆| 欧美freesex10一13| 国产成人无码一区二区三区在线| 久久婷婷久久一区二区三区| 蜜桃av噜噜一区二区三区| 成年免费A级毛片免费看| 公车校花小柔h| 99久久精品免费看国产| 欧美日韩精品久久久久| 国产欧美一区二区三区免费| 久久午夜免费鲁丝片| 美女视频黄a视频全免费网站色| 性一交一乱一视频免费看| 伊人久久精品亚洲午夜| 2018中文字幕在线| 日韩一本二本三本的区别青| 又湿又紧又大又爽a视频| 中文无码精品一区二区三区|