Design Of All Round Bottom Shoe With Narrow Enclosure

If you design a shallow bottom shoe with full bottom, you can make use of the narrow feature of the fence and leave no space between the shoes.

This is another way to design full bottom shoes.

The characteristics of the shallow surround shoes are narrow and long.

The size of the strip is narrowed, and the amount of wrinkled shoes will be reduced by adults. This is a relationship between scissors difference, and the narrow strip can be properly deformed without affecting the final shaping effect.

1. finished product drawing

As shown in figure 2-5-22, this is a side opening full bottom bottom shallow shoe, and the wrinkle of the toe is connected by stubble cross stitching.

There are stubble on the shoe cover, double rows of holes, pressure on the shoe cover, the pin holes on the fence are aligned with the second rows of holes in the shoe cover, the wrinkled head is not smooth, and is quite smooth, and accords with the style of the shallow shoe.

 

The shoe weir is relatively long and connects with the back pack.

The length of the bottom of the design should not exceed half the width of the heel of the sole.

The design of the whole package bottom shallow shoe is also completed first, and then according to the rule of the bottom shoe.

2. structure design drawing

As shown in figure 2-5-23, the shoe sole should not be stretched. It is necessary to have an accurate difference between the inside and outside, design the shoe cover and then design the punch position.

9/4.5, posterior segment 15/5.5.

The holes are also designed in the following areas: 24/6 and 9/6.

 

There is a back raised tongue behind the back pack, which has the function of lifting shoes, and also has the function of suture after concealing the seam.

3. make the basic model of shoe cover.

As shown in figure 2-5-24, press stubble on the shoe cover and double row holes. The first row is placed in the 2mm position, and the second row is placed at the distance of 3mm.

 

4. preparation of girth and back pack and sample plate

As shown in Fig. 2-5-25, there are punching positions and wrinkled boundary lines O'and A1 and A2 on the gird pattern.

There is stubble quantity and punching position on the back and the template.

5. design of shoe structure

Use the back pack and the template and the surrounding pattern as the replica board to design the shoe body, as shown in figure 2-5-26.

 

Trace the contour of the last bottom template, and the last bottom template has been included in the 3mm length.

According to the method of figure 2-5-18, we first design the rear package, and control the length of the bottom port and the length of the rear arc.

According to the method of wheel rotation, the contour of the rear part is designed to connect to the B point of the rear package and to the boundary line.

The length of the hole is basically not wrinkled, not confused with the front.

Similarly, according to the wheel rotation method, the contour of the front gear can be designed, and after practice, it can be completed easily.

The same method is used to design the contour line.

Figure 2-5-27 for shoe body.

 

The punching position of the front shoe of the shoe body is calculated according to the length difference between the fence strip and the shoe cover, and the total spacing of the wrinkles is determined and the spacing between each hole is determined.

The punching position of the rear gang does not change much, and is adjusted according to the original hole position.

The position of the rear pocket is larger than that of the upper one, and is redistributed according to the number of holes.

The position of punching is in the position of 2mm.

The distance between the double rows of holes on the cover is 3mm, while the rear row holes are relative when the string is slit, and the spacing strip is 1mm apart from the first row hole.

Because of the setting of pressing stubble, the position of the retaining strip is stable, and there will be no big deformation.

If you want to increase the spacing between the two rows of holes, the width should be increased.

Note that the distance between the double row holes behind the bags is also 3mm.

The basic template of the back bar and the back tongue is shown in figure 2-5-28.

The back bar and the back tongue should also be added with the amount of stubble, double row holes and 3mm spacing.

The back arc line of the back bar is made by splicing process, and then the tongue is used to cover the seam line.