Examples Of The Design Of Sandals

1. design of three quarter net Leather Men's sandals

Mesh leather is a kind of leather upper material woven with a leather mesh. The net leather made of dog skin has better flexibility. It is usually used in three sections of head, outer ear, tongue, and women's shallow leather sandals.

Using mesh materials to design sandals, mesh leather should be used on larger parts, and the edges of mesh skin should be loose, convex and irregular. It should be linked to the edges of parts such as shoes, ears and shoes, so as to improve the processing quality.

As shown in figure 4-2-1, mesh leather is used in front, middle, back, shoe and front Baotou.

In the shoe and the middle, the shoe mouth and the decorative shoe are connected to increase the strength around the net skin.

The design method is the same as the three section shoe design in the foundation structure.

The decorative parts should be designed at the back end of the front gang. The partition ratio of the former Baotou can be redistributed before the decoration bar.

Design of 2. tongue type perforated men's sandals

Punching and decorating is a common technology. It can increase permeability by regular drilling, and can be applied to all kinds of shoes.

As shown in figure 4-2-2, this tongue shoe is made of gallbladder structure, and the decorative holes are on the shoe covers and half round bars.

The tongue is tongue shaped, and the middle is connected by rubber bands.

The design method is the same as the whole tongue type gallbladder shoes.

After the design of the components is finished, mark the location of the holes.

3. the design of the rear empty rubber band sandals.

As shown in figure 4-2-3, this case is a rear empty structure for male sandals, and is connected by wide rubber bands.

The front shoe of the shoe is the shoe cover structure, and the mesh material is used on the back of the shoe to increase the permeability of the shoe.

According to the design of the shoe cover, the replica board is made and double line pick up is adopted.

4. the design of the whole tongue type women's sandals.

As shown in figure 4-2-4, the space is designed for the connection between the whole shoe tongue and the side of the side.

The structure of the long tongue is similar to that of the whole band, and the incision is cut at the 1/3 position of the tongue width.

The first two incisions are to sew the back band into the car line, and then cut the shoelace in the back.

The whole shoe is simple in line and made of thicker leather. All the edges of the parts are trimmed, and only a small number of stitches can be seen.

The front part is designed to switch to pick up, and then the shoelace is designed to bend the shoelace.

5. the design of women's sandals in the middle and the empty rooms

As shown in Fig. 4-2-5, the rear heel of the shoe has a rear empty structure. There are two holes in the waist socket, forming a middle rear empty structure.

Pay attention to the seam of the back of the shoe and continue to open.

The middle position of the shoe is designed with a clear rubber band to increase the opening and closing function.

There is an opening at the corner of the instep, though it can not solve the problem of picking up, but it can help wrinkle up when it is stretched.

The former is designed by conversion and seesaw method.

The edge of the inside of the full shoe has exposed parts and is still treated by wrapping.

As shown in Fig. 4-2-6, the figure (a) is a schematic diagram and a groove marking line.

When designing sandals with sandals, this complex markup is often encountered.

These complex lines can be simplified at design time, so the "aircraft board" shown in Fig. B appears.

The aircraft board is commonly known as the bottom plate of the sandals.

The lines of the graph (b) include the lines of the graph (a). The prominent part is the exposed inner bottom edge, which needs to be hemming; the part of the concave part is the part of the help foot and needs to polish the groove.

One board and two uses, each has its own place.

In the design of sandals, the design of aircraft boards is an integral part of structural design.

6. the design of the hollow lady's sandals with short shoes

As shown in figure 4-2-7, the waist of the shoe is empty, and the shoe cover and the back side are dark jointing.

The front shoe of the shoe has a short shoe cover, double line pick up, and the design method of figure 2-2-19 short cover shoe is the same.

Processing marks are required at the bottom.

Mastered the design of full shoes, and then carried out the design of the empty parts on the upper, thus forming sandals.