• <abbr id="ck0wi"><source id="ck0wi"></source></abbr>
    <li id="ck0wi"></li>
  • <li id="ck0wi"><dl id="ck0wi"></dl></li><button id="ck0wi"><input id="ck0wi"></input></button>
  • <abbr id="ck0wi"></abbr>
  • <li id="ck0wi"><dl id="ck0wi"></dl></li>
  • Home >

    How To Adjust The Stitching Machine And The Tension Pin Of The Sewing Machine

    2012/10/23 16:57:00 47

    Stretching NeedleCrossing BoardSewing Machine

     

    Some kinds of sewing machine

    Stretching needle

    The timing with the needle can be adjusted.

    For example, the three needle and five wire stitching machine can adjust the timing between the needle and the needle by adjusting the angle between the F00710004 and the front axle (F00708001).

    The best time to cooperate is when the needle goes down and the right needle moves into the tightened needle ring when the right needle moves to the right.



    The amplitude of the needle must be ensured: when the needle is swinging to the right extreme position, it can hook the needle when it returns to the left. The relationship between the needle and the hook is wrong: the relationship between the high speed needle and the crochet needle.

    The reason for this phenomenon is that the bottom and surface lines are not properly twisted on the fabric before the surface scissors are opened. This failure is not caused by a certain part of the problem. It needs to be checked and adjusted from several aspects.

    Line error: correct the thread again.

    Needle installation error: reinstall the needle correctly.

    When the needle moves to the far left, the distance between the tip of the needle and the left needle is 4.5-5.5mm.


    The installation height of the needle should be as high as possible, because if there is a needle jumping phenomenon before the scissors are opened, then when the scissors are opened, the surface line will emerge from the pinhole.

    Check whether the length of the bottom line is enough. If the bottom line is not enough, then the bottom line and the surface line can not be properly twisted when the seam is started, resulting in the surface line from the pinhole, but the upper and the needle of the needle.

    Over line panel

    The gap between below should enable the needle to pass smoothly.


    The installation height of the strut needle should be able to raise the needle line to the highest point when the needle is raised to the highest point. The chain line bending needle clamp plate pressure is too loose: Micro thread chain bending needle thread clamp nut.

    Its function is to loose the surface line after the keyhole is finished. When carrying out the next keyhole, it will provide enough surface line to the rotary shuttle with the take-up rod to prevent the surface line from coming out of the scissors due to the decrease of the supply line.

    The return quantity or height of chain thread Crochet is incorrect: re adjust according to the standard.

    Slide smoothly under the right needle to the back of the needle tip of the right needle (away from the operator side), so that when the right needle drops, it is easy to stop the sewing thread.


    When

    Flat seaming machine

    When the tip of the needle moves to the front of the left needle, the gap between the left needle and the tip of the needle should be 0.5-0.8mm.

    • Related reading

    繃縫機送布動作怎樣協調

    Equipment matching
    |
    2012/10/23 15:48:00
    32

    Troubleshoot Of Needle Baldness In Computer Sewing Machine

    Equipment matching
    |
    2012/10/23 14:58:00
    39

    Fault Handling Method Of Jumper In Electronic Keyhole Machine

    Equipment matching
    |
    2012/10/23 12:08:00
    33

    How To Deal With The Breakdown Of Single Needle Sewing Machine

    Equipment matching
    |
    2012/10/23 10:58:00
    22

    Difference Between Reverse Seam And Normal Seam Of Single Needle Sewing Machine

    Equipment matching
    |
    2012/10/23 10:06:00
    21
    Read the next article

    導致服裝促銷不到位的原因

    導致服裝促銷不到位的原因有服裝經銷商的費用截流,服裝銷售人員對形式的認知性偏差,市場的多變的環境以及執行力差等,新產品上市和處理滯銷品,應該加服裝促銷,否則只有增加庫存。

    主站蜘蛛池模板: 538精品在线视频| 国产美女在线一区二区三区| 国产专区在线视频| 久久国产加勒比精品无码| 黑人巨大sv张丽在线播放| 最近最新中文字幕高清中文字幕网 | 免费的毛片视频| 丁香婷婷六月天| 精品xxxxxbbbb欧美中文| 最新69国产成人精品视频69| 在线观看永久免费视频网站| 国产dvd毛片在线视频| 久久se精品一区二区影院| 翁想房中春意浓1-28| 成品网站nike源码1688免费| 国产女人好紧好爽| 亚洲人成电影青青在线播放| 午夜小视频在线| 日韩精品专区av无码| 国产中文欧美日韩在线| 中文午夜人妻无码看片| 精品一久久香蕉国产二月 | 热久久综合这里只有精品电影| 在线观看人成视频免费| 亚洲成av人片高潮喷水| freefron性中国国产高清| 熟妇人妻久久中文字幕| 国产精自产拍久久久久久蜜| 亚洲人成色77777| 香蕉视频污网站| 日韩三级一区二区三区| 四虎4hu永久在线观看| 一区二区三区四区精品视频| 波多野结衣和黑人| 国产最新精品视频| 亚洲av无码专区在线播放| 67194成人手机在线| 最近2019mv中文字幕免费看| 国产AV人人夜夜澡人人爽麻豆 | 91av手机在线观看| 最近中文字幕高清字幕8|