• <abbr id="ck0wi"><source id="ck0wi"></source></abbr>
    <li id="ck0wi"></li>
  • <li id="ck0wi"><dl id="ck0wi"></dl></li><button id="ck0wi"><input id="ck0wi"></input></button>
  • <abbr id="ck0wi"></abbr>
  • <li id="ck0wi"><dl id="ck0wi"></dl></li>
  • Home >

    The Design Of Whole Tongue Shoe -- Variant Design

    2010/6/10 11:25:00 75

    Integral Sampling

    The variant design of the tongue shaped shoe is displayed on the "whole". The amplitude of the change is bigger than that of the ear shoe and the pverse tongue type shoes. Sometimes it will feel completely different. However, the characteristics of the tongue shoe are still inseparable from the detailed analysis.



      

    (1) the design of the tongue shaped three quarter head women's shoes


    Tongue shaped women shoes are larger and exaggerated than men's lines, highlighting the characteristics of women.



    1. finished product drawing


    The design of female tongue shoes should be based on female prime last.

    The whole tongue shoe belongs to the structure of the dark door. As shown in figure 1-6-9, the width of the mouth door is located on the OQ line. When the width of the door is determined, take about 00'=30mm.



     The design of whole tongue shoe -- variant design

     

    2. structure design drawing


    With the former Baotou, the design starts from Baotou, and according to the design rules of the three head shoes, see 1-6-10.



     The design of whole tongue shoe -- variant design

     

    When designing the gang, draw the converted midline first, then design the V point of Baotou, like A.

    Point to shift back to the back line, also need to find the conversion length and actual length, also need to make 1 / 3 amount of dressing, finally, the outline of the former Baotou should be copied to the middle position.

    Because the position of the former Baotou and the gang is separated, to ensure the same contour, the replication method can only be used.


    After designing the contour line of the middle bar, the method of getting the corner of the corner is still the same after the contour line is taken. However, the contour curve of the drawing angle is relatively large, and it should be traced out by duplication.


    The other design process is the same as that of the tongue shaped men's shoes, and the method of making samples is the same.

    Because the design of the gang is quite special, its basic template is shown in figure 1-6-11.



     The design of whole tongue shoe -- variant design
     

      

    (two) the design of the whole tongue type men's shoes.


    The whole tongue type shoe refers to the whole tongue type shoes that the front and back sides keep opening.



    1. finished product drawing


    As shown in figure 1-6-12, the tongue, the front and the back are joined together, but there are decorative strips on the tongue, followed by heels at the heel, and the bayonet technology is used for the shoes.

    The bayonet bar connects the decorative strips and the back bags, although the size of the upper is relatively large, but it is not monotonous.



     The design of whole tongue shoe -- variant design

     

    The design of this shoe is similar to the continuous lingual style women's shoes in figure 1-5-27, which should be designed after the conversion.



    2. structure design drawing


    The shoe in figure 1-6-13 is straight, and it should take about 00'=15mm, and the length of the tongue will be around V "E".


     The design of whole tongue shoe -- variant design

     

    First, the decorative strip on the tongue is designed. The width is 14 to 16mm, and the length is over 12mm of the gate width. It is used to replace the cross arm reinforcement.


    The O point is designed in the decorative strip, according to the relationship between the stubble quantity, the contour of the front shoe tongue can be found.


    For positioning, take the AoV'line, take the A2E line to change and take off, and connect the equivalent quantity instead of the angle AoO'A2.


    Take the QO'Q'to make the QO'Q'= AoO'A2.


    Use the compasses to intercept the Q'point.

    The OQ line of the half panel is aligned with the O'Q'line of the design diagram, and the rear arc contour and the bottom contour line are traced from Q' to the intersection of the two bottom line.

    Then draw the front line of the bottom line before the top of the Qi, and finally connect the two bottom lines.


    After completing the design of the gang, make the difference between the inside and outside, and cut out the position of the rear package.


    Because of the difference between the height of the back group and the width of the door, the decoration bar should have the difference between the inside and outside.


    The bayonet bar is different from the mouthpiece. When processing, it directly covers the shoe and the line.

    The width of the card bar is 5mm, and the width of the bayonet bar is as follows:


    2 x (design width ten processing volume) + thickness =2X (5+-3) +2=18 (mm)


    The length of the bayonet bar is 2 * O'Q, which can be spliced on the side.


    Finish the difference between the bottom rib and the inside and outside.


    The method of making templates remains unchanged.



    Note: when marking the rules of the tongue and shoe trim, the method of operation is the same as that of the outer tongue type women's shoes.

    For the structure chart of the rear lift, it will move the tongue with the change of the position of the back, but the rules should return to the original position when it is stretched. Therefore, when marking the rules, keep the tongue intact, and then restore the original position to the original position.



    {page_break}


      

    (three) the design of women's shoes with Yuanbao style



    1. finished product drawing


    As shown in figure 1-6-14, the shoe tongue is missing, the waist of the shoe is slightly sinking, similar to the shape of the treasure, so it is named Yuan Baoxie.


     The design of whole tongue shoe -- variant design

     

    This shoe belongs to the open door.

    The location of the door is very important. Improper design will cause the problem of not wearing foot.


    Because the front end of the shoe cavity has the allowance, as long as the front tarsal bone is penetrated into the shoe cavity, the whole foot can be put in.

    Therefore, the key to designing the door position is not to exceed the position of the front tarsal bone.

    When designing tongue shaped shoes, O'points are used as the vertical line of the back midline, in order to control the location of the door.


    Generally speaking.

    The location of the door should not exceed 1 / 2 of the back line.



    2. structure design drawing


    The design of Yuanbao women's shoes should be converted to pick up method. To be exact, since the front and back sides are kept open, the method of lifting and changing shall be adopted.

    Take the center for the first 1 / 3 corner of the shoe, see figure 1-6-15.


     The design of whole tongue shoe -- variant design

     

    As shown in the figure, set the gate V "point" in the midpoint of VE, point the V'line as the vertical line of the VE line, and control the shape of the door.

    Find the P'point and make the outline of the shoe.


    For positioning and taking off line, find Ao point, do the conversion and take the line to find the A2 point.

    The equivalent quantity is replaced by AoO'A2.


    Set the 0'point at the corner of the shoe, and take the corner to make the Qo'o'= AoO'A2.


    Find Q'with compasses.

    First, the half panel is covered on the structural drawing, and the 0 point is fixed and then rotated to the half panel to reach the Q'point. The outline of the rear arc and the bottom section is traced.

    To make the newly designed shoe line smooth, round and smooth.

    Next, find the A2 point, add the 1 / 3 length difference, and then segment the front bottom line.

    Make the difference between the tension and the inside and outside.


    The method of making templates is the same as before.



       

    (four) the design of the ladies' slippers.


    If the shoe faces of the ladies' shoes are lengthened and the rear ones lowered, this will form a full pair of ladies' slippers, as shown in figure 1-6-16.

    This is a popular female shoe in recent years, using slippers to wear, using full shoe design.



     The design of whole tongue shoe -- variant design

     

    As shown in the figure, these shoes have both front and back sides, and should belong to full shoes.

    But the later gang was very low. When it appeared early, it had a height of 20mm or so. Later it turned out to be only 5 to lOmm high. When you wear shoes, you can only walk with your feet "dragging your shoes", so it's called full pair slippers.


    The surface of these shoes can be decorated in various ways, but the foundation structure is very simple.

    A designer once said with emotion: "when I first saw this shoe, I thought it was too simple. I didn't expect to go into production after the design was finished. There was no suitable pair of bandages.

    The heels of each shoe can't be raised. "

    Why?



    As mentioned earlier, the pformation of stilts itself is a mandatory stilt, that is, the need to use human methods to join the stilt angle, and then to eliminate the adverse factors by human methods.

    In such a way, it is impossible for people to join or to eliminate them.

    For ordinary full shoes, the latter is relatively high, and there is no obvious problem. However, for the full pair of slippers, the latter is very short. Once the sedan is not enough, it will cause trouble. The problem is that the height of the gang is not in place.


    As shown in Fig. 1 - 6-17, when the front arm is drawn into a straight line, the area of the front tip will be short of one angle.

    When the bandage is pushed, the part will be pushed up by the last. At this time, the area will be supplemented by the latter, and then pferred to the back to help the shoe.

    If you do not take the stilts, you will cause the heel design to be full of ladies' slippers. The door is taken at E and the height is taken at lOmm.

    Cross the E point as the vertical line of VE, control the outline of the door, and then connect the shoe outline.

    The center is set at the top 1 / 3 of the shoe, and the arc should be round.



     The design of whole tongue shoe -- variant design

     

    The design of the rear arc, the design of the front support, and the treatment of the bottom port are all the same as the previous ones.


    Finally, the template is made.


    • Related reading

    Design Of Tongue Shaped Shoes -- Design Of Tongue Shaped Men'S Shoes

    Learning Area
    |
    2010/6/10 10:27:00
    504

    The Design Of Whole Tongue Shoe -- Conversion And Take Off Principle Diagram

    Learning Area
    |
    2010/6/10 10:11:00
    210

    整舌式鞋的設計——設計特點

    Learning Area
    |
    2010/6/10 9:31:00
    98

    Where Does The Wave Of Fishtail Skirt Come From?

    Learning Area
    |
    2010/6/9 18:30:00
    70

    螺旋群如何打板?

    Learning Area
    |
    2010/6/9 17:47:00
    302
    Read the next article

    Hebei Launched Fur Class Yan Zhao Line Activities

    In June 5, 2010, the launching ceremony of the fur class Yan Zhao line was solemnly held at the Quyang Bridge Township Government in Zhengding County, Hebei province. The fur class Yan Zhao line activities were initiated by the fur industry association of Hebei Province, and sponsored by Hebei farmers' newspaper and Hebei fur industry association. The aim is to improve the breeding level of fur animals in Hebei Province, to increase farmers' income, to ensure the healthy and stable devel

    主站蜘蛛池模板: 波多野结衣新婚被邻居| 亚洲丶国产丶欧美一区二区三区| 九九免费精品视频在这里| 337p中国人体啪啪| 男男chinese同志gay露脸飞机| 日本免费一区二区三区最新| 国产开嫩苞实拍在线播放视频| 亚洲精品**中文毛片| 一级毛片美国一级j毛片不卡| 韩国三级中文字幕hd久久精品| 欧美成人精品三级网站| 天天久久综合网站| 吃奶呻吟打开双腿做受视频| 久久精品久久精品| 在线国产你懂的| 永世沉沦v文bysnow全文阅读| 国产麻豆入在线观看| 免费人成年轻人电影| 中文字幕一区二区三区乱码| 韩国全部三级伦电影在线播放| 日本护士xxxx黑人巨大| 国产日韩欧美精品一区| 亚洲明星合成图综合区在线| av片在线播放| 男女一进一出抽搐免费视频| 在线成年视频免费观看| 人人澡人人澡人人看添av| 一二三四区产品乱码芒果免费版| 男人日女人app| 好男人在线社区www| 可以看的黄色国产毛片在线电影| 一本一本久久a久久综合精品蜜桃 一本一本久久a久久综合精品蜜桃 | 97碰在线视频| 男女啪啪进出阳道猛进| 国内一级纶理片免费| 亚洲av永久无码一区二区三区| 1000部啪啪未满十八勿入 | 亚洲欧美成人一区二区在线电影 | 久久久久久成人毛片免费看| 饥渴难耐16p| 日本三级欧美三级人妇视频黑白配|