Home >

Design Of Women'S Round Shoes

2010/6/14 15:19:00 139

??? 日本語 Fran?ais English 中文

Women's round shoes are women's shoes with a round shape.

The shape of the round door is not well designed because almost all people have a clear concept of "circle", which is long, short, square, and not sharp.

1. product structure analysis

As shown in figure 3-2-1, this is a middle heel and plain round shoes, and the upper is very simple.

(1) the last type is a super long female shallow round top, with a long bottom 245mm and a rest allowance of 19. 5mm.

The shape of the last head is round head, which is suitable for designing women's round shoes.

Note: the change of the shape of the door of women's shoes is usually in harmony with the shape of the toe.

(2) the structure of women's round mouth shoes is a typical structure of women's shallow shoes, and other women's casual shoes are designed on the basis of women's round shoes.

The mouth door is located at Vo point, and belongs to the middle long face type.

(3) the components include three pieces, four pieces of front, back, and insurance covers.

Taking into account the material, the inside and outside of the gang is broken.

(4) insert the front side to press the back, and then press the stubble to 8mm, and the front need not fold, which can show the characteristics of the dermis.

(5) the special requirements require the design of the circular door outline.

The roundness and roundness of the door are not measured by compasses. It is seen by the eyes and is a feeling of people.

When designing a round door, do not draw with a compasses. The same door is drawn out by a compasses, and the round door with different flavor will be obtained by hand drawing.

Then, to what extent is the design of the portal be suitable?

Please make an experiment: dip your hands in the basin, then lift your hand to observe the drop of water drops.

A circular arc is formed on the front end of each bead.

When droplets are agglomerate, when water droplets are formed, when droplets are crumbling, when droplets fall, these arcs will show different shapes.

These circular arcs are different forms of performance. They are circular arc with different tension, and are circular arc with vitality.

To satisfy the needs of different customers with different circles of circular arc, this is the answer to the design of round door.

See the color picture L-4, which is a flat heel with round mouth shoes. The color picture L-5 is a middle heel big round shoe, and the color picture L-18 is a flat heel small round shoe.

The size of the door is also different from that of the round door shoes.

Although it is just an arc of round door, to design this arc, we must consider comprehensively the factors such as the shape of the last head (big round head, middle round head, small round head), the height of the last heel (flat heel, middle heel, high heel), the length of the shoe face (long front face, middle long face, short front face) and other factors.

{page_break}

2. structure design drawing

As you can see from figure 3-2-2, designing women's shallow shoes is simpler than designing full shoes.

(1) the dorsal midline connects the VJ line to the dorsal midline and extends to A.

Point.

(2) first design the outer shoe line to drop from 2 to 3mm after the 0 point, and then set the O'point. The midpoint position of the back height line between the O' point and the QQ point is increased by 1mm at the O point, then V perpendicular to the O "O'" perpendicular to the 25mm point.

The outer shoe contour is designed in the range of VO to O'to O "to Q".

For the width of the mouth, older people prefer to be a little wider. Full fat can enrich the shoes and show the charm of women.

But today's young people, with their bony beauty and bony feet, do not match their wide mouths, so quite a few people prefer slightly narrow mouths.

(3) in the design, the shoe mouth contour line is located at the O'point. The difference between the inside and outside of the shoe line is found by referring to the two back height lines, and the shoe line is designed on the O' point.

There are differences between the inside and outside arms in the position of the ankles. The two differences between the shoe and ankle bones should be linked up.

The shape of the door is round and round, and it is not easy to produce a single side. It can duplicate the contour line on the other side of the middle line, or cut out the template to see the overall effect.

The shape of the door is not satisfied. It can be modified until satisfactory, as shown in figure 3-2-3.

(4) make the difference between the inside and outside of the rear arc.

The amount of 1/2A is added to Li Huai, and the amount of 1/2A is reduced to the outside.

(5) make break line.

Through the F point, the vertical line of the back midline is intersected with the OQ line to get the broken line.

(6) make the waist waist craft sew.

The 1/3 sigma y is added to the help line.

(7) make the bottom stretch.

According to 12mm, 13mm, 14mm and 15mm, add the bottom to stretch the weight.

(8) make the difference between the bottom and the outside.

According to the result of the test, the bottom line of the inside and outside is distinguished.

{page_break}

3. design high heels and flat women's round shoes.

The design of high heel round shoes is the same as that of designing heels.

As shown in figure 3-2-4, there are differences between the arms and legs, the waist of the shoe, the arc of the heel and the bottom of the mouth.

The shoe's outer arms are not broken, but only in the middle, there is a broken arm, and the waist craft is added to the rear support of Li Huai.

The design of flat heel round shoes is the same as the design of middle heel shoes, see figure 3-2-5.

Shoes, shoes waist, back arc, bottom mouth have the difference between inside and outside.

The shoes inside and outside are not broken, the heels are low, and there is no machining.

{page_break}

Comparing the structural design of the middle heel, high heel and flat female round shoes, it is found that their lines are different even when they have the same location.

Why?

Because the design of the female shoe's shoe contour should be decided according to the shape of the shoe last.

We will put the flat heel, the middle heel and the high heel last in front of us. It is easy to find that there is a difference in the shape between the bottom and the bottom part from the comparison between the three.

Among them, the curve of high heel last is more obvious, and the change of heel last is relatively gentle.

In the eyes of experienced designers, it is very easy to distinguish between three kinds of heel height. When designing the shoe line, it is necessary to refer to the change of the contour of the last bottom, especially at the waist.

The shape changes of the last bottom line can be divided into three sections: the first section is the corrugated line at the front part of the last part, which is the basis for setting the shape of the juice gate, that is, the round last door with the round door, the square door, the prescription door and so on, so it is easy to coordinate.

The second section is the line of the toes and toes. This is the basis for designing the arc of the door. The bending of the Jimo gate should be coordinated with the bottom line, including the difference between the inside and outside.

The third segment is the corrugated line on the waist socket, that is, the upward trend of the shoe line should be in line with the waist curve.

Generally speaking, high heeled women's shallow shoes are easy to design, because the changes of the bottom line are prominent, and the design of the shoe's "bow shaped" curve is easy to coordinate with the bottom line.

If you now ask "is it easy to design women's shallow shoes," your answer must have been thinking.

Because the key to designing women's shallow shoes is to control the lines, which has a concept of "non straight and non curved".

Not only shallow shoes, including all kinds of boots and shoes, but also a straight line shape when observing the shape of products.

If you draw a straight line with straight ruler, you will not achieve the design effect, and you must use the curve design to produce the effect.

In the same way, the shape of some products is the shape of curves. If you really use a curve design, it will not be in place, and only the straight line design can express the original effect.

This is the meaning of the concept of non straight Philippines.

For example, the design of a former Baotou, if cut out is a straight line shape, paste on the last surface will become a curve.

What if we do not plan a straight line of Baotou?

We must design a curve to ensure that it is straight after sticking last.

For example, the broken line of women's shallow shoes is a curve on the finished shoes. If the straight line is processed on the sample, the curve will be produced after the stretch.

Some of the shapes of the rear shoes appear straight lines, while curves should be used in the actual design.

Because there is a difference between the last surface and the last surface, we should be familiar with the last shape, understand the last shape, and apply these differences from perceptual to rational.

The reason for this is that the design of lines is too important for women's shallow shoes.

Using the same last type, the same size and the same round mouth shoes, if the design lines are different, different round mouth shoes will be obtained.

This is the "round mouth door with one hundred different flavours that you can draw by hand" before.