• <abbr id="ck0wi"><source id="ck0wi"></source></abbr>
    <li id="ck0wi"></li>
  • <li id="ck0wi"><dl id="ck0wi"></dl></li><button id="ck0wi"><input id="ck0wi"></input></button>
  • <abbr id="ck0wi"></abbr>
  • <li id="ck0wi"><dl id="ck0wi"></dl></li>
  • Home >

    Analysis Of Fault Detection Method For Industrial Sewing Machine System

    2013/9/6 21:45:00 59

    Industrial Sewing MachineSewing MachineSewing Machine Industry

    < p > < a href= "http://www.91se91.com/news/index_c.asp" > industrial sewing machine < /a > electric control system generally has the function of intelligent automatic fault detection. We can determine what faults the system appears according to the different alarm codes of the system, and further determine which part of the system has problems.

    After determining the fault code, we can use corresponding processing methods to maintain. Different brands of < a href= "http://www.91se91.com > > electric control system < /a > may adopt different fault codes, but the specific categories of their faults are not very different.

    In addition, there are obvious and specific notes on the instructions of the electronic control system.

    < /p >


    < p > industrial a href= "http://www.91se91.com/news/" > sewing machine < /a > during maintenance, technicians can observe the machine with vision and compare with the normal working condition of the system, so as to narrow down the fault area or locate the fault location directly.

    For example: observe whether the controller and the display surface have no scars, whether the plug is off or not, and whether the lead wire is disconnected, whether the components of the circuit board are burnt, broken feet, and pins collide.

    < /p >


    < p > sometimes the operator will replace the corresponding parts on the equipment by using new parts to determine whether the parts are faulty, the location of the fault or the specific components of the fault.

    During maintenance, we should start with large parts and replace them step by step until we find out the faults.

    This method is mainly used in the case of adequate fittings or good electrical control system.

    < /p >


    < p > for example, when maintaining the AC servo system, it is necessary to determine whether it is a system problem. Generally, the method of changing the normal control box is used to determine whether the fault is an industrial sewing machine or a control box.

    In the maintenance of circuit boards, this method is also used to replace the "suspected" fault components in the circuit with good components, observe the changes of the controller and determine the location of the fault.

    < /p >


    < p > sometimes the electromagnet function of the electrical control system of the industrial sewing machine fails to alarm. It can break the solenoid joint or further disconnect the supply voltage of the electromagnet so as to determine whether there is any fault in other circuits.

    When the AC servo controller works normally, the working voltage of each point in the machine indicates the working condition of the machine within a certain range. When the fault occurs, the working voltage will inevitably change.

    The measuring voltage method is to use multimeter to check whether the working voltage of each test point of the plug and circuit board in the machine is larger or smaller.

    When measuring, it is necessary to measure the AC voltage and DC voltage with different gears of multimeter.

    The voltage measurement method is usually measured under < a href= "http://www.91se91.com" > machine < /a > electrified condition. Therefore, attention should be paid to single handed operation, safety first.

    < /p >

    • Related reading

    Printing Occupies 2014 Of The Spring And Summer Show.

    Technology Extension
    |
    2013/9/6 18:19:00
    76

    Textile And Garment Industry: Look Forward To New Technology Of Printing And Dyeing With No Water And Less Water

    Technology Extension
    |
    2013/9/5 14:45:00
    39

    功能型織物涂層技術前景分析

    Technology Extension
    |
    2013/8/31 20:39:00
    15

    免維護直接驅動系統讓織機更穩定

    Technology Extension
    |
    2013/8/13 20:13:00
    17

    Military Textiles Follow The Footsteps Of Science And Technology To Green Environmental Protection

    Technology Extension
    |
    2013/8/1 15:03:00
    47
    Read the next article

    外貿單證流程是什么?

    外貿單證就是指在國際結算中應用的單據、文件與證書,憑借這種文件來處理國際貨物的支付、運輸、保險、商檢、結匯等。因其特殊性,需要不同于一般的單據,主要是運輸單據,包括提單、商業發票、匯票、裝箱單、產地證等。

    主站蜘蛛池模板: 狠狠色综合一区二区| 中文亚洲成a人片在线观看| 18禁裸男晨勃露j毛免费观看| 亚洲国产最大av| 欧美性大战久久久久久| 国产精品电影在线| 亚洲日本乱码在线观看| 1717国产精品久久| 欧美性狂猛bbbbbxxxxx| 国产精品一区二区电影| 亚洲av永久青草无码精品| groupsex娇小紧的5一8| 男女一边摸一边做爽爽| 日本三级在线观看中文字| 国产三级在线观看播放| 中文字幕亚洲欧美日韩不卡| 网友偷自拍原创区| 岛国AAAA级午夜福利片| 佐佐木明希哔哩哔哩| 99久在线观看| 欧美性色欧美a在线播放| 夜先锋av资源网站| 亚洲欧美精品一中文字幕| 67194成人手机在线| 欧美人与物VIDEOS另类| 国产日韩精品欧美一区| 久久婷婷激情综合色综合俺也去 | 91啦中文成人| 欧美乱强伦xxxxx高潮| 国产夫妻在线视频| 久久99国产精品久久99| 粗大的内捧猛烈进出在线视频| 大胸年轻的搜子4理论| 免费看欧美一级特黄α大片| 99在线视频网站| 欧美人与动性xxxxbbbb| 国产又爽又黄无码无遮挡在线观看 | 免费国产污网站在线观看| AV片在线观看免费| 欧美又粗又长又爽做受| 国产精品福利一区二区久久|