• <abbr id="ck0wi"><source id="ck0wi"></source></abbr>
    <li id="ck0wi"></li>
  • <li id="ck0wi"><dl id="ck0wi"></dl></li><button id="ck0wi"><input id="ck0wi"></input></button>
  • <abbr id="ck0wi"></abbr>
  • <li id="ck0wi"><dl id="ck0wi"></dl></li>
  • Home >

    A Clever Trick Today: Hand-Made Shoes Rack.

    2014/10/25 17:18:00 215

    Shoe RackHandmadeFashion

       Shoe cabinet The effect is good, but if you have a narrow pass, the shoe cabinet will be useless. Even so, there is no need to be upset. The man in the house can actually refer to our plan and create a beautiful and concise display stand for his family's shoes with his own skillful hands. The placement of shoes is skillfully made of steel tubes. It does not need too much wood, and it will not be bulky.

    Simple materials and tools for making wooden shoe shelves.

    The length, width and thickness of the timber are 210cm * 7cm * 1.8cm (size is for reference only, and can be adjusted according to needs) 3 screw thread nuts, screwdrivers, screwdrivers, 4mm diameters and 1m lengths. Steel saw , ruler, semicircle instrument, pencil, sandpaper, drill bit (3mm and 5mm respectively).

    Simple wooden shoe rack making method:

    Step one: determine the size

     

    First, determine the overall size of the shoe rack according to the wood on your hand. The reference given in the picture: the length of the two supporting plates on the side of the shoe rack is 60cm, and the width is 7cm according to the original size of the timber. The length of the two legs of the shoe rack is 25cm and the width is 7cm. Mark the length on the wood with a pencil, but do not rush to see it first, because we need to cut an inclined plane on the timber on this length basis so that the shoe rack forms an inclination angle so that the shoe does not fall easily. You can first measure 60cm on wood, draw a vertical line with pencil, then use the semicircle instrument to measure the angle of 15 degrees based on the vertical line, then draw a line at the corresponding angle. Along this line, the timber can be sawn out and the two side supporting plates are processed equally. Then, it was made in wood on the supporting legs, so that 4 pieces of timber with 15 degrees bevel were obtained. Sanding the rough section with sandpaper, so that the wood will not scratch the ground.

    Simple manufacturing method of wooden shoes rack

      

    The second step: drilling.

    Now we have to determine the location of the metal beam. Due to the different types and sizes of family shoes, the distance between beams should be different in order to keep all kinds of shoes firmly on the shoe rack. For example, for the location of slippers, the distance between beams is only 2.5cm. The position of the hole should be diagonal, so that the heels and shoes can be stressed, so that they can be "suspended" on the shoe rack.

    Simple manufacturing method of wooden shoes rack

      

    The diagonal holes are not very well positioned. Here is a trick: we will use two holes as a group. First, determine the location of two holes from the edge of the board. The width of the board is 7cm. We set the vertical distance between the two holes to be 4cm, then the two holes should be 1.5cm from the edge of the board. The rest of the holes will be used as reference. You can draw two parallel lines in pencil, and the distance between lines is the vertical distance 4cm of the hole.

    Then, according to the different spacing of the crossbeam, determine the pitch size at the horizontal position of a hole to mark, then mark the position of the other hole on the other vertical line. When all the holes are marked, they can start drilling. Here, the diameter of the hole for the fixed beam is 5mm, the diameter of the three holes of the fixed foot and the side board is 3mm. The corresponding planks can be stacked together to drill holes.

    The third step: assemble wooden boards.

    For beauty, you can hide your feet in the side panels, and then use screws and nuts to fix them.

    The fourth step: install crossbeam.

    Then install the crossbeam. The 3 thread steel prepared in advance is divided into 9 roots, each with a length of 33cm. We must be careful when cutting thread steel. We can try to fix it first and then sawing again, so as not to roll the steel stick along with the saws. 8 beams used for shoes rack are fixed on the side planks with nuts respectively. The thickness of the side board also takes up the length of some beams, so the final fixed beam is about 30cm. The rest of the rebar is used to connect two legs. Shoe rack The supporting force.


    • Related reading

    A Small Suit With A Skirt And A Lady'S Temperament.

    DIY life
    |
    2014/10/22 21:38:00
    169

    布藝包:讓你對生活有不一樣的見解

    DIY life
    |
    2014/10/16 0:35:00
    34

    小小耳環讓我們煥發無限光輝

    DIY life
    |
    2014/10/16 0:27:00
    40

    DIY: Let Me Fall In Love With Fashionable And Dynamic Life.

    DIY life
    |
    2014/10/14 21:41:00
    20

    有趣的布藝手工讓你解壓和開心

    DIY life
    |
    2014/10/14 21:31:00
    70
    Read the next article

    What Laws Can Be Applied To Foreign Contractual Obligations?

    The so-called contract refers to the agreement between the parties to establish, alter or terminate the relationship between civil rights and obligations. The so-called debt of a contract is a relationship arising from the conclusion of a contract.

    主站蜘蛛池模板: 中文字幕乱码人在线视频1区| 国产在线播放免费| 亚洲欧美日韩国产精品专区| a级毛片免费观看视频| 福利视频第一页| 欧美黑人乱大交| 在线免费中文字幕| 亚洲视频中文字幕在线| 99国产精品99久久久久久| 激情成人综合网| 成年人在线免费看视频| 国产XXXX99真实实拍| 亚洲va久久久噜噜噜久久| jizz.日本| 日韩高清在线中文字带字幕| 国产成人十八黄网片| 亚洲成人第一页| jazzjazz国产精品一区二区| 狼群社区视频免费下载观看| 在线观看国产一区二区三区| 亚洲欧洲自拍拍偷午夜色| **毛片免费观看久久精品| 欧洲mv日韩mv国产mv| 国产美女mm131爽爽爽毛片| 亚洲国产成a人v在线观看| 国产香蕉精品视频| 日本毛茸茸的丰满熟妇| 又粗又猛又黄又爽无遮挡| 久久不见久久见免费影院www日本| 色多多视频网站| 女人张开腿让男人做爽爽| 亚洲精品中文字幕乱码三区| a在线免费观看视频| 精品久久欧美熟妇WWW| 大尺度视频网站久久久久久久久| 亚洲欧美日韩在线精品一区二区| 亚洲激情小视频| 日本a级视频在线播放| 国产中文字幕电影| 一区二区三区国模大胆| 毛片a级毛片免费观看品善网 |