• <abbr id="ck0wi"><source id="ck0wi"></source></abbr>
    <li id="ck0wi"></li>
  • <li id="ck0wi"><dl id="ck0wi"></dl></li><button id="ck0wi"><input id="ck0wi"></input></button>
  • <abbr id="ck0wi"></abbr>
  • <li id="ck0wi"><dl id="ck0wi"></dl></li>
  • Home >

    Leather Footwear Industry Standard (3)

    2008/2/20 12:05:00 42251

    Leather footwear industry standard (3)


    Test method for shoelace breaking force


    1 theme content and scope of application


    This standard specifies the test method of shoelace breaking force.


    This standard applies to the determination of shoelace breaking force of various materials.


    2 Principle


    The force needed to pull the sample cut off the shoelace on the tensile machine is the breaking force of the shoelace.


    3 test equipment


    3.1 tensile testing machine


    3.1.1 maximum load should not exceed 250N (250kgf).


    3.1.2 load range can be divided into three files: 500N (0~50kgf): 1000N (0~100kgf); 2500N


    (0~250kgf) the test uses a minimum load range.


    3.1.3 accuracy: + 1%.


    3.1.4 has strong fixtures and leather pads in metal clamps.


    3.1.5 stretching speed can be adjusted to 100 + 10mm/min.


    4 sample


    4.1 the length of the specimen between the clamping units is 200 mm.


    4.2 at least 5 shoelaces.


    4.3 the temperature of the sample is 20 + 10, and the humidity is 65 + 5%. The condition is adjusted by 48h.

    Wet sample determination does not state adjustment, but the sample should be placed at 20 + 10 C, and the concentration of 1% of the fatty alcohol polyoxyethylene ether aqueous solution wetted 1H.


    Note: if there is no constant temperature and humidity equipment, use the saturated solution of pure ammonium nitrate or pure ammonium nitrite in the dryer, then dry and dry it into the thermostat with a temperature of 20 + 10 degrees Celsius, so that the above can be achieved in the dryer.


    Standard temperature and humidity.


    5 test conditions


    5.1 stretching speed: 100 + 20mm/min.


    5.2 ambient temperature: room temperature.


    6 test procedure


    6.1 dry sample determination.


    6.1.1 stretching speed: adjusted to specified value.


    6.1.2 pfer the tension indicator to zero.


    6.1.3 adjust the two clamp edge 200 mm.


    6.1.4 take out the sample from the thermostat and immediately insert the two sides of the sample into the upper and lower two fixtures.


    6.1.5 actuate the position machine to record the force value of the specimen during fracture.


    6.2 wet sample determination


    6.2.1 removed the sample from the aqueous solution of "fatty alcohol polyoxyethylene ether" and made the water out and tested according to 6.1 tests.


    Note: Cotton shoe lace can be measured only by dry sample, and chemical fiber products shoelace should be dry and wet.


    7 test results


    7.1 the arithmetic result is taken as the arithmetic average, and the unit is expressed as "N", and the effective digit to the digit.


    7.2 the test results of the specimen slipping or breaking at the clamp and the breaking force relative to the mean deviation of 10% are invalid.


    7.3 the effective test data for calculating the average value must not be less than 5.


    8 test report


    The test report should include the following:


    A. indicates that the test is carried out according to this standard (ZBY75022-90).


    B. test number, name, specification, production unit;


    Pretreatment conditions of C. test;


    D. laboratory temperature, humidity and stretching speed;


    E. test results;


    F. test personnel and date.

    • Related reading

    Leather Shoes Industry Standard (2)

    Shoemaking technology
    |
    2008/2/20 12:03:00
    42253

    Leather Footwear Industry Standard (1)

    Shoemaking technology
    |
    2008/2/20 12:02:00
    42283

    Introduction Of SA8000 Standard Certification

    Shoemaking technology
    |
    2008/2/20 12:01:00
    42067

    Leather Sole

    Shoemaking technology
    |
    2008/2/20 12:00:00
    42050

    Introduction Of The Latest National Standard For Shoes No.

    Shoemaking technology
    |
    2008/2/20 12:00:00
    42361
    Read the next article

    Test Method For Longitudinal Stiffness Of Leather Shoes

    The longitudinal stiffness test method for leather shoes 1: subject content and application scope. This standard specifies the test method for the longitudinal flexural rigidity of leather shoes. This standard is applicable to the determination of the longitudinal bending rigidity of leather shoes. The 2 principle is to fix the heel of the hook and load it at its front end, causing it to bend and deform and measure the bending deflection of the hook so as to calculate the bending rigidity of the

    主站蜘蛛池模板: 国产日韩av在线播放| 欧美怡红院在线| 尤物在线影院点击进入| 好男人官网资源在线观看| 吃奶摸下的激烈免费视频播放| 久久亚洲sm情趣捆绑调教| 黄瓜视频在线播放| 日本爽爽爽爽爽爽在线观看免| 国产又粗又猛又黄又爽无遮挡| 久久精品免费全国观看国产| 麻豆国产成人AV在线| 激情影院在线观看十分钟| 成年人在线看片| 吃奶摸下的激烈免费视频播放 | 亚洲乱码一区av春药高潮| 网址在线观看你懂的| 欧洲国产成人精品91铁牛tv| 在线精品国产一区二区三区| 亚洲精品无码久久久久| 777国产偷窥盗摄精品品在线| 欧美日韩加勒比一区二区三区| 天天躁夜夜踩狠狠踩2022| 啊好深好硬快点用力别停免费视频| 中国一级特黄毛片| 阿v免费在线观看| 成年女人男人免费视频播放| 国产成人a大片大片在线播放| 久久国产高潮流白浆免费观看| 足鞋臭脚袜奴交小说h| 成人在线手机视频| 伊人影视在线观看日韩区| 一级**爱片免费视频| 狠狠综合久久av一区二区| 好男人在线社区www| 亚洲精品无码乱码成人| 相泽亚洲一区中文字幕| 日本黄色一级视频| 又爽又黄有又色的视频| 99久热只有精品视频免费观看17| 疯狂吃奶freesex| 国产精品欧美一区二区三区|